Bedienungsanleitung Numark cdmix-1 (Seite 4 von 28) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

161519

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

REAR PANEL FEATURES

1. LINE INPUTS (RCA) – Connect line-level devices, such as CD players, samplers or audio interfaces, to these inputs.

2. RECORD OUTPUT (RCA) – Use standard RCA cables to connect this output to a recording device, such as a CD

recorder or tape deck. The level of this output is based upon pre-master levels.

3. MASTER OUTPUT (RCA) – Use standard RCA cables to connect this output to a speaker or amplifier system. The

level of this output is controlled by the MASTER FADER on the top panel.

4. MASTER OUTPUT (BALANCED) – Use XLR cables to connect this Master output to a speaker or amplifier system.

The level of this output is controlled by the MASTER FADER on the top panel.

5. MIC INPUT – Connect a 1/4" microphone to this input.

6. POWER IN – Use the included power adapter to connect the mixer to a power outlet. While the power is switched off,

plug the power adapter into the mixer first, then plug the power adapter into a power outlet.

7. POWER SWITCH – Turns the mixer on and off. Turn on the mixer after all input devices have been connected and

before you turn on amplifiers. Turn off amplifiers before you turn off the mixer.

MIXER FEATURES

1. CHANNEL FADER – Adjusts the audio level on the corresponding channel.

2. INPUT SELECTOR – Selects the input source to be routed to the corresponding channel. Input jacks are located on the

rear panel.

3. CROSSFADER – Blends audio playing between Channels 1 and 2. Sliding this to the left plays Channel 1 and sliding to

the right plays Channel 2.

Note: The crossfader is user-replaceable if it should ever wear out. Simply remove the facepanel, then remove the

screws holding it in position. Replace the fader with a quality authorized replacement from your local Numark retailer

only.

4. FADER START – Enables or disables “fader start.” When fader start is enabled, moving the crossfader toward a side

will cause that channel to start playing.

5. MIC GAIN – Adjusts the audio level of the microphone signal.

6. MIC ON/OFF – Turns the microphone input on or off.

7. MASTER FADER – This control adjusts the output volume of the Program mix.

8. STEREO / MONO – Adjusts the Program mix for stereo or mono operation.

9. CHANNEL TREBLE – Adjusts the high (treble) frequencies of the audio of the Program mix.

10. CHANNEL MID – Adjusts the mid-range frequencies of the audio of the Program mix.

11. CHANNEL BASS – Adjusts the low (bass) frequencies of the audio of the Program mix.

12. STEREO LEVEL INDICATOR – Monitors the audio level of the Program mix.

13. CUE MODE SELECTOR – Selects the audio that is sent to the headphones. Switch it to “1+2” to hear Channels 1 and 2

in the Cue channel.

14. CUE GAIN – Adjusts the audio level of the Cue channel.

15. HEADPHONES – Connect your 1/4" or 1/8" headphones to this output for cueing and mix monitoring.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark cdmix-1 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info