Bedienungsanleitung Numark CM1000R (Seite 9 von 14) (Englisch)

23426

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

CM1000/CM1000R

- The Leader in DJ Technology

CROSSFADER

16. Replaceable Crossfader - achieves clean segues

between the two input channels selected by the

Crossfader Assign.

In this example "Hard left" selects Channel 1 and

"Hard right" selects Channel 4. With the crossfader

centered, both assigned channels are live. Use the

crossfader for fast and seamless segues from one

selected channel to the other.

Note:

The crossfader is replaceable in case of

failure. Simply remove all knobs from the facepanel

and unscrew the 5 screws that hold it in place.

Then remove the 2 fader screws that hold the

crossfader to the subchassis, lift it out and

disconnect its cable. Re-attach the new crossfader

and replace the faceplate and knobs back onto the

unit - you’re back in business!

17. Crossfader Slope – determines how quickly the

audio from the opposing side of the crossfader

activates. A tight curve (hard right) turns on the

opposing audio signal with very little crossfader

movement. A loose curve (hard left) makes very

long and smooth segues in transition.

18. Crossfader Assign Knob - determines which input

channel will be heard when the crossfader is moved

towards the knob and which channel is fader start.

Note:

All channels not assigned will remain active.

19. Fader Start – activates the crossfader to send play

and cue commands to your auto-start Numark CD

player or other popular brand using pulse

technology. For fader start, attach your mixer to a

remote start CD player using industry standard

1/8”(3.5mm) cables. When you move the crossfader

toward the active channel, the attached CD player

will start. When it is moved away, that side will cue

(similar to pressing the cue button).

OUTPUTS

20. 4-Band EQ control – adjusts the master output

according the setting on the rear panel. When the

unit is set for +/- 6 or 12dB the unit will increase or

decrease the frequency area adjusted.

21. Master Fader – to control the overall output level.

22. Panning – adjusts the balance of right and left

audio.

23. Stereo/Mono toggle - adjusts the Master output for

stereo or mono operation.

24. Stereo Auto Peak Hold Level Indicator- quickly

and accurately tracks level of audio sent to it by the

meter assign. The red LEDs for +3dB, +5dB and

+8dB hold program peaks for a second or two. With

peak metering, it's OK to be "in the red" as long as

+5dB or +8dB aren't constantly lit. When using as a

master output meter, set the crossover, equalizer

and power amp inputs to avoid distortion at each

step in the audio chain. Proper attention to the peak

meter results in the punchiest possible sound

without audible distortion. When used to adjust

the PFL levels, accurately match channel levels

with the Pre-fader gain controls before mixing them

together. The idea is to properly match PFL inputs,

not the input with the stereo output meter!

25. Zone Faders - controls speaker volume for a remote

zone or booth monitors.

NOTE:

This can also be used to supply line level

audio to a lighting controller or to lights that are

sound activated.

26. Power Indication LED – indicates when power is

applied to the unit and the rear panel power switch

is on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark CM1000R Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info