Bedienungsanleitung Numark DM1635 (Seite 7 von 20) (Englisch)

23484

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

DM1635

GUIDED TOUR OF FEATURES AND OPERATING

INSTRUCTIONS...

If the DM1635 is your first mixer, please read this entire

manual before you begin operation.

If you are an experienced DJ simply replace your old

mixer. The DM1635 can be rack-mounted or used as a

free-standing unit (five 19" rack unit spaces).

INSTALLATION AND OPERATION

Study the Connections Diagram on page 13. First,

connect all stereo input sources. Next connect your

microphone(s) and monitor headphones. Make sure all

faders are at "zero" and the unit is off. Finally, connect

the stereo outputs to the power amplifier(s) and/or audio

sources. Plug the DM1635 into AC power. Now you

are ready to switch it on.

The DM1635 is divided into six functional blocks:

Input, Crossfader, DJ Mic, Master/Booth Output,

Equalizer, and BEATKEEPER. It is important to learn

how each of these work.

CHANNEL INPUTS/CONTROLS SECTION

1. Channels 1, 2, 3 & 4 Input Toggle Switches

select which source will be live to that channel based on

what you have connected to the rear panel input

section.

2. The Input Faders are low-noise, low-impedance,

high-quality, smooth Alps™ faders. These control

individual source levels in the mix.

3. Channel Cue Assign. The Cue pushbuttons are

used to route channel audio to the Monitor Section.

The channel faders do not control the Cue send

volume.

4. Effect Send (Channels 1-4). Depress these

buttons when you want the signal from any input

channel to be routed to the Send Out Jacks. The

channel faders do not affect the signal levels which are

routed to the send output.

CROSSFADER SECTION

5. The Crossfader Assign knob to the left of the

crossfader lets you choose which input channel will be

heard when the crossfader is in the far left position.

6. The Replaceable Crossfader achieves clean

segues between the two selected input channels.

Off1 2 3 4

"Hard left" selects the channel set up of the Assign

Left knob. In this example it is Channel 1. "Hard right"

selects the channel set up on the Assign Right

knob. In this example it is Channel 4. With the

crossfader centered both assigned channels are live.

Use the crossfader for fast and seamless segues from

one selected channel to the other. To turn off the

crossfader simply turn both knobs all the way to the

left.

Note: The crossfader is user replaceable in case of

failure. Simply unscrew the two large screws which

hold it in place, lift it out and disconnect it’s cable. Re-

attach the new crossfader and screw the mounting

plate back onto the unit - you’re back in business!

7. The Crossfader Assign knob to the right of the

crossfader lets you choose which input channel will be

heard when the crossfader is in the far right position.

Numark - The Proven Leader in DJ Technology

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark DM1635 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info