Bedienungsanleitung Numark Mixtrack Pro 3 (Seite 6 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

618122

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Rear Panel

1. Master Output (RCA): Use standard RCA

cables to connect this output to speakers or an

amplifier system.

2. USB: Sends USB MIDI data to control various

software parameters.

Performance Pad Modes

The upper row of pads has different functions depending on their mode: Manual Loop Mode,

Auto Loop Mode, and Sample Mode.

To select a mode, hold down the Pad Mode button and

press one of the upper pads.

An LED under the pad section indicates the currently selected

mode.

Manual Loop Mode: Hold Pad Mode and press the pad marked Manual Loop (silkscreened

above the pad) to assign the lower 4 pads to the functions listed below:

• Loop In – Sets the beginning of a loop. After a Loop Out point is set, when this button is

pressed again, it will allow for fine adjustment of the Loop In point.

• Loop Out – Sets the end point for the loop. When this button has been pressed after a

Loop Out point has been set, it will allow for fine adjustment of the Loop Out point.

• On/Off – When this is pressed inside a loop, this will turn the loop off. When pressed

outside a loop, this will activate the loop and start playback from its Loop In point. If a loop

has not been set, this button will have no effect.

• Loop x1/2 – Cuts the currently playing loop in half. Press Shift + Loop x1/2 to double the

length the currently playing loop.

Auto Loop Mode: Hold Pad Mode and press the pad marked Autoloop to assign the lower 4

pads to the functions listed below:

• Auto 1 – Sets and starts playback of a 1-beat autoloop.

• Auto 2 – Sets and starts playback of a 2-beat autoloop.

• Auto 4 – Sets and starts playback of a 4-beat autoloop.

• Auto 8 – Sets and starts playback of an 8-beat autoloop.

Sample Mode: Hold Pad Mode and press the pad marked Sampler to assign the lower 4

pads to the functions listed below:

• Sample 1 – Plays the sample assigned to Sample Pad 1.

• Sample 2 – Plays the sample assigned to Sample Pad 2.

• Sample 3 – Plays the sample assigned to Sample Pad 3.

• Sample 4 – Plays the sample assigned to Sample Pad 4.

Beatmixing with MIXTRACK PRO 3 and Serato DJ intro

Below is an example of how to mix tracks using MIXTRACK PRO 3 and Serato DJ Intro:

1. Load tracks onto the decks of Serato DJ Intro by using the Load 1 and Load 2 buttons

on MIXTRACK PRO 3.

2. Move the crossfader all the way to the left on MIXTRACK PRO 3.

3. Turn the Cue Mix knob all the way to the right to ‘PGM’.

4. Play the track that is loaded on Deck 1.

5. Play the track that is loaded on Deck 2 and match it’s BPM to Deck 1’s track. To match

the BPM, press Deck 2’s Sync button on MIXTRACK PRO 3.

6. Once the BPM is matched, move the crossfader on MIXTRACK PRO 3 to fade between

Deck 1 to Deck 2.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark Mixtrack Pro 3 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info