Bedienungsanleitung Numark Mixtrack Pro II (Seite 6 von 28) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

618128

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

PAD MODE COMMANDS

The lower row of pads has different functions depending on their mode: Looping Mode, Sample Mode, or Hot

Cue Mode.

To select a mode, hold down the SHIFT button and press one of the lower pads. An LED under

the pad section indicates the currently selected mode.

Looping Mode: Press Shift + Loop In to assign the lower 4 pads to the functions listed below:

• Loop In – Sets the beginning of a loop. After a Loop Out point is set, when this button is pressed again, it

will allow for fine adjustment of the Loop In point.

• Loop Out – Sets the end point for the loop. When this button has been pressed after a Loop Out point has

been set, it will allow for fine adjustment of the Loop Out point.

• Reloop – When this is pressed inside a loop, this will turn the loop off. When pressed outside a loop, this

will activate the loop and start playback from its Loop In point. If a loop has not been set, this button will

have no effect.

• Loop x1/2 – Cuts the currently playing loop in half. Press Shift + Loop x1/2 to double the length the

currently playing loop.

Sample Mode: Press Shift + Loop Out to assign the lower 4 pads to the functions listed below:

• Sample 1 (S1) – Plays the sample assigned to Sample Pad 1.

• Sample 2 (S2) – Plays the sample assigned to Sample Pad 2.

• Sample 3 (S3) – Plays the sample assigned to Sample Pad 3.

• Sample 4 (S4) – Plays the sample assigned to Sample Pad 4.

Hot Cue Mode: Press Shift + Reloop to assign the lower 4 pads to the functions listed below:

• Cue 1 (C1) – If a cue point has not already been set for the loaded track, this control will mark Cue Point

1. If a cue point has already been set, this control will jump to Cue Point 1.

• Cue 2 (C2) – If a cue point has not already been placed on the loaded track, this control will mark Cue

Point 2. If a cue point has already been set, this control will jump to Cue Point 2.

• Cue 3 (C3) – If a cue point has not already been placed on the loaded track, this control will mark Cue

Point 3. If a cue point has already been set, this control will jump to Cue Point 3.

• Delete Cue (C) – Press this button, and then press one of the other pads in the row to delete its cue point.

SIDE PANEL

1. Headphone Output – Connect headphones to these 1/4”

and 1/8” jacks for monitoring the signal. The headphone

volume is controlled using the Cue Gain knob.

2. Microphone Input – Connect a standard dynamic

microphone to this 1/4” jack.

3. Mic Gain – Adjusts the level for the microphone input.

REAR PANEL

1. Master Output (RCA) – Use standard RCA cables to connect

this output to a speaker or amplifier system.

2. USB – Sends USB MIDI data to control various software

parameters.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark Mixtrack Pro II Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info