Bedienungsanleitung Numark NS6 (Seite 5 von 36) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

618149

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

REAR & FRONT PANEL FEATURES

REAR:

34 4

FRONT:

17 17

16 15 14 13 13

1. POWER IN – Use the included power cable to connect NS6 to a power outlet. While the power is switched off, plug the

cable into NS6 first, then plug the cable into a power outlet.

2. POWER SWITCH – Turns NS6 on and off. Turn on NS6 after all input devices have been connected and before you

turn on amplifiers. Turn off amplifiers before you turn off NS6.

3. USB – This USB connection sends and receives audio and control information from a connected computer.

4. MASTER OUTPUT (XLR) – Connect this low-impedance XLR output to a PA system or powered monitors. The level of

this output is controlled with the MASTER knob on the top panel.

5. MASTER OUTPUT (RCA) – Use standard RCA cables to connect this output to a speaker or amplifier system. The

level of this output is controlled by the MASTER knob on the top panel.

6. BOOTH/ZONE OUTPUT (RCA) – Use standard RCA cables to connect this output to a booth monitoring system. The

level of this output is controlled by the BOOTH/ZONE knob on the top panel.

7. LINE INPUTS (RCA) – Connect line-level devices, such as CD players, samplers or audio interfaces, to these inputs.

8. MIC INPUT (1/4") – Connect a 1/4" microphone to this input. Microphone controls are located on the top panel.

9. LINE | PHONO INPUTS (RCA) – Connect your audio sources to these inputs. These inputs can accept both line and

phono-level signals.

10. LINE | MIC SWITCH – Flip this switch to the appropriate position, depending on the device connected to the LINE |

PHONO INPUTS. If you are using a microphone, set this switch to "MIC." If using a line-level device, such as a CD

player or sampler, set this switch to "LINE."

11. LINE | PHONO SWITCH – Flip this switch to the appropriate position, depending on the device connected to the LINE |

PHONO INPUTS. If you are using phono-level turntables, set this switch to "PHONO" to provide the additional

amplification needed for phono-level signals. If using a line-level device, such as a CD player or sampler, set this switch

to "LINE."

12. GROUNDING TERMINAL – If using phono-level turntables with a grounding wire, connect the grounding wire to these

terminals. If you experience a low “hum” or “buzz”, this could mean that your turntables are not grounded.

Note: Some turntables have a grounding wire built into the RCA connection and, therefore, nothing needs to be

connected to the grounding terminal.

13. HEADPHONES (1/4" or 1/8") – Connect your 1/4" or 1/8" headphones to this output for cueing and mix monitoring.

14. HEADPHONE VOLUME – Adjusts the volume level of the headphone output.

15. SPLIT CUE – When this switch is in the ON position, the headphone audio will be "split" such that all channels sent to

CUE are mixed to mono and applied to the left headphone channel and the Program mix is mixed to mono and applied

to the right channel. When the switch is in the OFF position, Cue and Program audio will be "blended" together.

16. CUE BLEND – Turn to mix between Cue and Program in the Headphone channel. When all the way to the left, only

channels routed to CUE will be heard. When all the way right, only the Program mix will be heard.

17. CROSSFADER ASSIGN – Routes the audio playing on the corresponding channel to either side of the crossfader (L or

R), or bypasses the crossfader and sends the audio directly to the Program Mix (center, "|").

18. CROSSFADER SLOPE – Adjusts the slope of the crossfader curve. Turn the knob to the left for a smooth fade (mixing)

or to the right for a sharp cut (scratching).

19. FADER START – Enables or disables “fader start” on the corresponding side of the crossfader. When fader start is

enabled on one side, moving the crossfader toward that side will cause the Deck to start playing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark NS6 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info