Bedienungsanleitung Numark NS7 II (Seite 6 von 64) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

618134

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Mixer Controls

5. Input Selector: Set this switch to the desired audio source from this channel: PC (a track

playing on that layer in the software), Mic 2 or Line (a device connected to the Mic 2 Input or

Line Input on NS7II's rear panel). Please note that the Line/Phono selector switches on

NS7II's rear panel must also be set properly. Also, a channel's controls will only send MIDI

information when its Input Selector is set to PC.

Important: Do not set more than one channel's Input Selectors to Mic2; doing so can cause

unwanted feedback or distortion.

6. Gain Trim: Adjusts the pre-fader, pre-EQ audio level of the corresponding channel in the

software.

7. LED Meters: Monitors the audio levels of the corresponding channel.

8. Channel Treble: Adjusts the high (treble) frequencies. When Touch Mode is activated,

touching this knob will mute the corresponding channel's high frequencies (an "EQ kill").

9. Channel Mid: Adjusts the mid-range frequencies. When Touch Mode is activated, touching

this knob will mute the corresponding channel's mid-range frequencies (an "EQ kill").

10. Channel Bass: Adjusts the low (bass) frequencies. When Touch Mode is activated, touching

this knob will mute the corresponding channel's low frequencies (an "EQ kill").

11. Channel Fader: Adjusts the audio level on the corresponding channel in the software.

12. PFL: Press this button to send this channel's pre-fader signal to the Cue Channel for

monitoring. When engaged, the button will be lit. By pressing one PFL button at a time, you

will cue that channel alone (and deactivate PFL monitoring for the other channels). To cue to

multiple channels simultaneously, press the PFL buttons for those channels at the same

time.

13. Crossfader: Blends audio between the channels assigned to the left and right side of the

crossfader.

14. Master Volume: Adjusts the output volume of the Program Mix.

15. Booth/Zone Volume: Adjusts the output volume of the Booth Output mix.

Playback Controls

16. Platter: Controls the Audio Pointer in the software.

17. Start Time: Controls the rate at which the platter regains its normal playback speed.

18. Stop Time: Controls the rate at which the platter slows to a complete stop ("brake time").

19. Play / Pause: This button pauses or resumes playback.

Press and hold Shift and then press this button to "stutter-play" the track from the last set

Cue Point.

20. Cue: When the Deck is paused, you can set a Temporary Cue Point by moving the Platter to

place the Audio Pointer at the desired location and then pressing the Cue Button.

During playback, you can press the Cue Button to return the track to this Temporary Cue

Point. (If you did not set a Temporary Cue Point, then it will return to the beginning of the

track.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark NS7 II Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info