Bedienungsanleitung Numark NS7 II (Seite 10 von 64) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

618134

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

30. Slicer: This Pad Mode button switches the pads between two modes: Slicer Mode and Slicer

Loop Mode. When the button is unlit, the first press will always select Slicer Mode.

Important: Your track must have a set Beat Grid for Slicer Mode or Slicer Loop Mode to

work.

• Slicer Mode: The eight pads represent

eight sequential beats—"Slices"—in the

Beat Grid. The currently playing Slice is

represented by the currently lit pad; the

light will "move through the pads" as it

progresses through each eight-Slice

phrase. Press a pad to play that Slice—

hold it down if you want to keep looping

it. When you release the pad, the track will resume normal playback from where it would

have been if you had never pressed it (i.e., as if the track had been playing forward the

whole time).

Press the Parameter < or Parameter > button to decrease or increase the Slice

quantization. Press and hold Shift and then press the Parameter < or Parameter >

button to decrease or increase the Slice Domain size.

• Slicer Loop Mode: The pads behave identically to the pads in Slicer Mode, except the

eight-Slice phrase will loop rather than moving forward continuously through the track.

Track Controls

31. Strip Search™: The length of this strip represents the length of the entire track. Place your

finger on a point along this sensor to jump to that point in the track. (If you want to scroll

through a track, we recommend using your computer rather than running your finger along

the strip.)

32. Slip / Clear: When using the software's Beat Grid, press and hold this button and move the

Platter to "slip" (i.e., shift or slide) the entire Beat Grid to the left or right.

Press and hold Shift and then press this button to delete the entire Beat Grid.

Important: Your track must have a set Beat Grid for the Slip / Clear button to work.

33. Adjust / Set: Press and hold this button and move the Platter to "warp" the entire Beat Grid.

Press and hold Shift and then press this button to set a Beat Marker at the Audio Pointer's

current location.

Important: Your track must have a set Beat Grid for the Adjust feature to work. Also, using

the Adjust feature will change the track's BPM.

34. Slip Mode / Motor Off: Press this button to enable or disable Slip Mode. In Slip Mode, you

can jump to Hot Cue Points, trigger Loop Rolls, or use the Platters, while the track's timeline

continues. In other words, when you stop the action, the track will resume normal playback

from where it would have been if you had never done anything (i.e., as if the track had been

playing forward the whole time).

Press and hold Shift and press this button to activate or deactivate the corresponding

Platter's motor. This will not affect the track's playback.

Slice 1

Slice 2 Slice 3

Slice 4

Slice 5

Slice 6 Slice 7

Slice 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark NS7 II Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info