Bedienungsanleitung Numark X5 (Seite 5 von 24) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

618169

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

7. EQ:

• Treble (Input Level High EQ): Adjusts the high (treble) frequencies of the corresponding

channel. Turning the knob completely to the right increases the level, turning the knob completely

to the left decreases the level to "off." This frequency "kill" control allows for unique mixing styles.

• Middle (Input Level Midrange EQ): Adjusts the mid-range frequencies of the corresponding

channel. Turning the knob completely to the right increases the level, turning the knob completely

to the left decreases the level to "off." This frequency "kill" control allows for unique mixing styles.

• Bass (Input Level Low EQ): Adjusts the low (bass) frequencies of the corresponding channel.

Turning the knob completely to the right increases the level, turning the knob completely to the

left decreases the level to "off." This frequency "kill" control allows for unique mixing styles.

8. LINE / PHONO / TRANS SWITCH (Input Selector Switch): These three-position toggles select what

input source is engaged among the connected units – and a flash position to allow rapid transforming

(audio signal "kill") effect.

9. CHANNEL FADER (VCA Fader): Adjusts the audio level on the corresponding channel.

Note: This fader is user replaceable if it should ever wear out. Simply remove the facepanel and then

remove the screws holding it in position. Replace the fader with a quality authorized replacement from

your local Numark retailer.

10. CHANNEL FADER CONTOUR: Adjusts the slope of the channel fader curve. Flip switch to the left for

a smooth fade or to the right for a sharp cut.

11. REVERSE BUTTON (Channel Fader Reverse Control): Activation of this switch can reverse the

fader direction.

CUEING / MONITOR CONTROLS

12. STEREO LEVEL INDICATOR – Monitors the audio level of the Program mix or Cue Channel,

depending on the position of the METER ASSIGN button.

13. METER ASSIGN BUTTON: Determines whether audio from the Program mix or the Cue channel is

sent to the stereo level indicator.

• When MASTER is indicated, this meter displays the stereo output levels of your mixed signal

(Program Mix).

• When CH1 – CH2 is indicated, the meter shows the pre-fader levels of channels 1 and 2 (Cue

channel). You can use the channel "Gain" and "EQ" controls to match the levels of input signals

while cueing.

14. CUE GAIN KNOB (Headphone Level): This rotary control adjusts the levels of the headphones

connected to the front panel input.

15. CUE TONE KNOB (Headphone Tone Control): This rotary knob adjusts the tone of the headphone

output. The knob can be raised and lowered to hide away by pressing it down.

16. CHANNEL CUE SLIDER: Channels 1 and 2 can be previewed using this mini-crossfader. Sliding this

to the left plays the left channel-1 and sliding to the right plays the right channel-2.

17. CUE / MASTER BUTTON: When lit, only the Program mix is heard. When off, only the Cue channel is

heard.

18. HEADPHONES: Connect your 1/4" headphones to this output for cueing and mix monitoring.

Headphone output controls are located on the top panel. The Volume should always be set at its

lowest setting while connecting and disconnecting headphones to prevent damage to headphones

and/or your hearing.

CROSSFADER CONTROLS

19. CROSSFADER (Digital VCA Crossfader): This slide fader blends audio between CH-1 and CH-2. Its

action can be modified with the "Mode," "Slope", and "Direction" controls. This digital mixer uses

digital VCA technology to accurately determine slider position. Both the VCA and Digital technologies

combined allow for some very powerful effects.

Note: This fader is user-replaceable if it should ever wear out. Simply remove the facepanel and then

remove the screws holding it in position. Replace the fader with a quality authorized replacement from

your local Numark retailer.

20. CROSSFADER CONTOUR: Adjusts the slope of the crossfader curve. Flip switch to the left for a

smooth fade (mixing) or to the right for a sharp cut (scratching).

21. CF REVERSE: Activation of this switch reverses the assignment of CH-1 and CH-2 on the crossfader.

OUTPUT CONTROLS

22. MASTER KNOB: Adjusts the Master output level.

23. BOOTH KNOB: Adjusts the Booth output level.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark X5 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info