685860
14
Zoom out
Zoom in
Vorherige Seite
1/160
Nächste Seite
14 ProMax Pressure Automatic 6000/8, Pressure Well Automatic 6000/8
Horizontal installation of the pump
with the stand
(Only ProMax Pressure Automatic
6000/8)
The pump can be horizontally installed
with the stand in a shallow tank or well.
The pump has to be aligned exactly hor-
izontally.
Ensure that the water to be pumped
does not contain any sand.
How to proceed:
E
1. Remove the Allen screws.
The stand consists of two sections.
2. Push two mounting feet onto each stand
section.
3. Push three rubber pads each into the
grooves of the opening of the stand sec-
tions.
Fit rubber pads to both stand sec-
tions.
4. Push both stand sections onto the
pump.
The stand sections should be spaced
as far apart as possible to ensure the
stability of the pump.
OPERATION
The pump control system (flow control)
measures the flow and switches the pump
off if the water flow stops.
The pump switches off when there is in-
sufficient water, protecting it from being
damaged by running dry.
In automatic mode, the pump control
system switches the pump on and off.
The integrated non-return valve prevents
water from flowing back into the pump
from the pressure hose when it is switched
off. The non-return valve also prevents
damage to the pump resulting from water
hammer.
Automatic mode
The pump switches off automatically
when no more water is used and the max-
imum pressure in the pressure line is
reached.
The pump switches on automatically
when water is used and the pressure in
the pressure line falls below 3.5 bar.
WARNING
Dangerous electrical voltage!
Death or severe injury from electrocu-
tion.
Only connect the pump to the power
supply when there are no persons in or
reaching into the water.
Before stepping into or reaching into the
water, switch off all units located in the
water.
Switching on the unit
Insert the power plug into the socket.
The pump is ready for operation.
Switching off the unit
Disconnect the power plug.
When the pump is switched off, resid-
ual water in the hose may flow back
and out of the pump intake.
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Oase ProMax Pressure Well 6000-8 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info