Bedienungsanleitung Oce OP1020 Advanced Operation Guide (Seite 149 von 162) (Englisch)

47348

149

Zoom out

Zoom in

Vorherige Seite

1/162

Nächste Seite

Appendix

ADVANCED OPERATION GUIDE Appendix-17

Glossary

Additional memory An additional memory (optional) is used for increasing the memory

capacity of this machine. In this machine, a memory can be added for the

copier functions and the printer functions respectively. (For copier: 16 MB,

32 MB, 64 MB, and 128 MB/for printer: 32 MB, 64 MB, 128 MB, and 256

MB) For DIMM that can be used in this machine, contact your dealer.

AppleTalk AppleTalk offers file sharing and printer sharing and it also enables you to

utilize application software that is on another computer on the same

AppleTalk network.

APS (Auto Paper Selection) This mode will automatically select copy paper of the same size as the

original.

Default Gateway This indicates the device, such as a computer or router, that serves as the

entrance/exit (gateway) for accessing computers outside of the network

that you are on. When no specific gateway is designated for a destination

IP address, data is sent to the host that is designated as the Default

Gateway.

DHCP (Dynamic Host

Configuration Protocol)

This is a protocol that automatically resolves the IP address, Subnet Mask

and Gateway address on a TCP/IP network. Use of DHCP minimizes the

load of network administration, especially on network environments with a

large number of client computers where it is not specifically necessary to

assign a separate IP address to each client, including printers.

dpi (dots per inch) This indicates the number of dots printed per inch (25.4 mm) as a unit for

expressing resolution.

EcoPrint This is a printing mode that reduces toner consumption. Pages printed in

the EcoPrint mode are lighter than pages printed in the normal mode.

Emulation This refers to emulation of other manufacturers’ printers. The printer

emulates operation of the following printers: PCL6, KPDL, KC-GL, Line

Printer, IBM Proprinter, DIABLO 630, and EPSON LQ-850.

Form Feed Timeout While data is being sent to a printer, some pauses may occur. At this time,

the printer waits for the next data without making a page break. Form feed

timeout is a function to wait only a preset amount of time before it executes

an automatic page break. After the waiting period begins, once the

designated amount of time is exceeded, the printer will automatically

process the currently received data and print it out. If the machine has

received no print data for the last page, the printer ends processing of that

job without outputting paper.

IEEE1284 This is a standard used when connecting a printer to a computer, and was

established by the Institute of Electrical and Electronic Engineers in 1994.

IP Access control This is a function to prohibit access to this machine from a host with an IP

address that is not approved.

IP Address (Internet Protocol

Address)

The Internet Protocol address is a unique number that represents a

specific computer in a network. The format of an IP Address is four

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oce OP1020 Advanced Operation Guide Seite 149

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info