Bedienungsanleitung Oce OP1020 Operation Guide Command Center (Seite 22 von 25) (Englisch)

47363

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

COMMAND CENTER

6-12 Advanced > Management / E-mail: SNMP

The SNMP protocol is used for providing and transferring management information

within the network environment. Should an error occur such as

Add Paper

, the printing

system can automatically generate a

trap

, an error message sent to up to two

pre-determined trap recipients.

6-13 Advanced > Management / E-mail: Maintenance

The machine can obtain maintenance information at a specified time. The report for the

total printed page is sent by e-mail.

Item Description

Read Community The read community can be used like a password. The default read

community name is

public

. When a management application sends an

SNMP request to read a value, it must include the correct read community

name or the request will be rejected by the printing system.

Write Community Similar in function to the read community, but used in SNMP requests to

write (change) a value.

sysContact The MIB-II sysContact object, usually the email address of the network

administrator.

sysName The MIB-II sysName object, usually the host or domain name of the printing

system.

sysLocation The MIB-II sysLocation object, usually the location information of the

printing system.

Authentication Traps Check On to enable or Off to disable the MIB-II EnableAuthenTrap object. If

enabled, an SNMP trap is generated when an attempt to read or write is

made using an incorrect community name. The trap is sent to the configured

trap address.

Trap Community The SNMP trap community name to be used when the printing system

generates a trap.

Trap IP Address The IP address which will receive the trap.

Trap IPX Address The IPX address which will receive the trap.

Selected Errors Select the events which will cause a trap to be generated including Low

Toner, Add Toner, Paper Jam, Add Paper, Cover Open, and All Other Errors.

Item Description

Equipment ID This sets the ID number of the system. Any number can be set. (max. 15

characters)

Recipient Address Configures where the Maintenance Notification is sent.

Note: Each address is delimited by a ;(semicolon), and up to 200

characters can be registered.

Subject Configures the Subject in the Maintenance Notification e-mail. If any of the

strings starting with a % listed in the below is found in the Subject box, that

string will be converted and output.

• %printer = Model

• %serial = Serial Number

• %etheraddr = MAC Address

• %equipid = Equipment ID

Scheduled Report Interval Sets the time or interval for sending the status information. Events will be

reported at the specified interval.

• None: No report is sent.

• Monthly: Sends on the specified day of specified month.

• Weekly: Sends on the specified day of every week.

• Daily: Sends at the specified time of every day.

• Hourly: Sends at the specified interval every hour.

Note: If a specified day does not exist in the month, such as the 31st, the

last day of the month is used as the specified day.

Run once now Clicking the Run once now button immediately sends a report.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oce OP1020 Operation Guide Command Center Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info