47405
15
Zoom out
Zoom in
Vorherige Seite
1/68
Nächste Seite
4-2
4. Selecting the Printer Settings
Item
1 Interface selection
Sets the interface that will be used for printing. The
currently selected interface will be highlighted. The printer
will automatically switch to the appropriate interface for
printing.
2 Parallel TX/RX mode
Sets the transmission and reception mode when the
printer is connected to your computer with a parallel
interface.
3 Baud rate
4 Data bit length
5 Stop bit length
6 Parity
7 Protocol
8 NetWare On/Off
9 NetWare Frame Type
Sets the NetWare Frame type.
0 TCP/IP On/Off
! DHCP On/Off
@ IP address
# Subnet Mask
$ Gateway address
% Ether Talk On/Of
^ Network Card Status Page print out
Prints out a Status page for the Network Card as well,
when the standard Status Page (page 4-1) or that for use
by your service representative (page 4-47) are printed out.
A more detailed Status Page will be printed out together
with the Service Representative Status Page print out.
Available settings
Parallel, Network, USB, Serial,
Option
Auto, Normal, High Speed,
Nibble (high)
1200, 2400, 4800, 9600, 19200,
38400, 57600, 115200
7, 8
1, 2
None, Odd, Even, Ignore
DTR(positive)&XON/XOFF,
DTR (positive), DTR (negative),
XON/XOFF, ETX/ACK
Off, On
Auto, 802.3, Ethernet 2, 802.2,
802.3 SNAP
Off, On
Off, On
Enter the appropriate network
address.
Enter the appropriate network
address.
Enter the appropriate network
address.
Off, On
Off, On
Remarks
Option is displayed only when the
optional network card is installed.
Serial is displayed only when the
optional serial interface is installed.
Displayed only when the Serial
interface is installed.
Displayed only when the Serial
interface is installed.
Displayed only when the Serial
interface is installed.
Displayed only when the Serial
interface is installed.
Displayed only when the Serial
interface is installed.
Displayed only when the NetWare
setting is turned On.
4-2 Interface Settings
About the interface settings
It is possible to perform interface settings for the 17 items shown in the following chart.
For the most efficient use of the printer functions, select the various settings according to your printing needs.
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Oce OP1030 Operations Guide Printing System Functions wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info