Bedienungsanleitung Oce OP15 Operations Guide Printing System Functions (Seite 28 von 87) (Englisch)

47516

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

3-5

3. Memory Card / RAM Disk

3-3-5 Reading print data

Perform the following procedure when you want to read print data that has been saved on a Memory Card or RAM Disk.

* In 20 ppm copiers, reading print data is accomplished from the operation panel on the copier itself. Refer to “2. Printer Settings (20 ppm

copier)” on page 2-1 for information on the appropriate procedure.

* Verify beforehand that the Memory Card is in a write-enabled state and that the RAM Disk is turned ON.

* To verify saved data and the corresponding partition name, it is helpful to print out the Partition List. Refer to “3-3-7 Printing out the Partition

List” for information on printing that list.

* In 20 ppm copiers, Partition List print out is accomplished from the operation panel on the copier itself. Refer to “2. Printer Settings (20 ppm

copier)” on page 2-1 for information on the appropriate procedure.

Procedure

1 Open an MS-DOS Prompt in Windows.

2 Type in the command to read data and then press the ENTER key.

[Example] To read the print data entitled “SAMPLE.txt” from a Memory Card

* To read the data from a RAM Disk, simply change the “A” parameter to “0”.

C:\WINDOWS>ECHO !R! RWER R,A,2,“SAMPLE.txt”; EXIT;>LPT1

3 Print out of the corresponding data will begin.

3-3-6 Deleting print data or font data

Perform the following procedure when you want to delete print data or font data that has been saved on a Memory Card or RAM Disk.

* In 20 ppm copiers, deleting data is accomplished from the operation panel on the copier itself. Refer to “2. Printer Settings (20 ppm copier)”

on page 2-1 for information on the appropriate procedure.

* Verify beforehand that the Memory Card or RAM Disk contains the data that you want to delete.

* To verify saved data and the corresponding partition name, it is helpful to print out the Partition List. Refer to “3-3-7 Printing out the Partition

List” for information on printing that list.

* In 20 ppm copiers, Partition List print out is accomplished from the operation panel on the copier itself. Refer to “2. Printer Settings (20 ppm

copier)” on page 2-1 for information on the appropriate procedure.

Procedure

1 Open an MS-DOS Prompt in Windows.

2 Type in the command to delete data and then press the ENTER key.

[Example] To delete the print data entitled “SAMPLE.txt” from a Memory Card

* To delete the data from a RAM Disk, simply change the “A” parameter to “0”.

* To delete font data, simply change the “2” parameter to “1”.

C:\WINDOWS>ECHO !R! RWER D,A,2,“SAMPLE.txt”; EXIT;>LPT1

3 Deletion of the corresponding data will begin.

4 Print out the Partition List to verify whether or not the data was deleted properly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oce OP15 Operations Guide Printing System Functions Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info