Bedienungsanleitung Oce OP15 Operations Guide Printing System Functions (Seite 44 von 87) (Englisch)

47516

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

2. Windows XL Driver

2-6

2-5 Output Tab

■ Output to:

Specifies the location of ejection of printed copies.

Selection is possible when the optional Job Separator and or Finisher are installed.

[Inner Tray] .................................Copies will be ejected onto the Inner tray.

[Separator Tray] .........................Copies will be ejected into the optional Job Separator.

[Finishing Tray] ..........................Copies will be ejected into the optional Finisher. (Only available in the 20 ppm copier)

* In order to set the location of ejection for the Job Separator or Finisher, it is necessary to first perform the setting for that optional

equipment under “Device Options” on page 2-7.

* Paper sizes and types that are acceptable for use with the Job Separator are as follows:

Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), Statement (5 1/2" x 8 1/2"), A3, A4, A5, Folio (210 mm x 330

mm), JIS B4 and JIS B5

Paper types: Plain, Letterhead, Recycled and Color

* Paper sizes, types and source of paper feed that are acceptable for use with the Finisher are as follows:

Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), A3, A4, Folio (210 mm x 330 mm), JIS B4 and JIS B5

Paper types: Plain, Letterhead, Recycled and Color

Source of paper feed: Any tray EXCEPT the Bypass Tray

■ Copies

Specifies the number of prints to be made. Select between 1 and 999 copies by clicking on the arrows at the right of the field or by typing

the desired number directly into the field. The factory default setting is “1”.

■ Collate

When you are printing more than one copy of one or more pages, it is

possible to sort the printed copy sets.

* It is necessary to create a RAM disk. (Refer to “RAM disk” on page 2-7)

* If you select to turn on the “Staple” setting below, it is necessary to

select “Collate” here.

Example: If the “Collate” option is selected, it is possible to print out

2 sets of the same copies.

■ Staple

Stapling is possible if the optional finisher is installed.

* Stapling is only available with 20 ppm copiers.

* The following settings are required before stapling is possible:

(1) “Device Options” setting in the “Device Settings” Tab

Select “Internal Finisher” and “RAM Disk”.

(2) “Output” Tab

Select “Finishing Tray” as the “Output to” setting and select “Collate” as well.

* Paper sizes, types and source of paper feed that are acceptable for stapling are as follows:

Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), A3, A4, JIS B4 and JIS B5

Paper types: Plain, Letterhead, Recycled and Color

Source of paper feed: Any tray EXCEPT the Bypass Tray

Note

The location of the staples will depend upon the orientation of the paper and the direction of the printed image. Thus, when you click on

either of the options (“Upper Left” and “Upper Right”) a message will be displayed in order to verify the orientation of the paper.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oce OP15 Operations Guide Printing System Functions Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info