Bedienungsanleitung Oce OP15 Operations Guide Printing System Set-up (Seite 15 von 22) (Englisch)

47519

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

3. Troubleshooting

3-2 When an error code or error messages appears…

If an error code or message appears on the operation panel, first check the following tables for cause of the trouble and then perform the

corresponding procedure. For more detailed information, refer to the Instruction Handbook for your copier as well as the Instruction Handbook for

any optional equipment that is installed in your machine.

Error Indications in the 15 ppm

copier

If “Prt” is displayed and the Memory Overflow / Data Error indicator flashes while the machine is in the copier

mode, an error has occurred with the printer functions of this machine. Press the Printer key and check the cause

of the error. Refer to the following tables for the corresponding error code and appropriate correction procedure.

Error code

(15 ppm copier)

E01

E02

E03

E04

—

E05

E06

—

Display message

(20 ppm

copier

)

—

Set drawer.

CLOSE PAPER DRAWER.

—

Add paper in drawer.

XX size (XXX)

ADD PAPER IN DRAWER.

XX SIZE (XXX)

Place paper in drawer.

PLACE PAPER IN PAPER DRAWER.

—

Out of staples.

Add staples.

STAPLER EMPTY.

ADD STAPLES.

Cannot staple different size

Cannot staple.

CANNOT STAPLE.

Procedure

A paper jam has occurred. Remove the jammed paper.

The drawer has run out of paper or a paper jam has occurred. Add paper or

remove the jammed paper, as appropriate.

One or both drawers are not set properly in the printer. Insert both drawers

securely.

The size of paper selected for printing does not match the size of paper in the

drawer. Replace the paper in the drawer with that of the correct size.

*If you want to force-print onto the current size of paper, press the Start key. If you

want to switch to and print from a different drawer, press the Paper Select key

until the desired drawer is selected. If you want to cancel the printing operation

completely, press the Stop/Clear key.

The size or type of paper selected for printing does not match the size or type of

paper in the drawer. Replace the paper in the drawer with that of the correct type.

*If you want to force-print onto the current size or type of paper, first press the

Printer key to switch to the printer mode. Next, the “GO” command. If you want to

switch to and print from a different cassette, press the Paper Select key until the

desired cassette is selected and then press the Enter key. If you want to cancel

the printing operation completely, first press the Printer key to switch to the printer

mode. Next, select the “CANCEL” command and then press the Enter key.

The drawer has run out of paper. Add paper.

One of the covers is open. Close the covers securely.

The finisher (option) has run out of staples. Refer to the Instruction Handbook for

the finisher and replenish the staples.

Stapling was not possible because there are different sizes of paper stacked

together. Remove all paper from the finisher.

The amount of paper stacked in the finisher has exceeded the acceptable capacity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oce OP15 Operations Guide Printing System Set-up Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info