Bedienungsanleitung Oce OP15 Operations Guide Printing System Set-up (Seite 16 von 22) (Englisch)

47519

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

3. Troubleshooting

Error code

(15 ppm copier)

—

E23

E30

E40

—

E60

E70

E71

E72

E73

Display message

(20 ppm

copier

)

No duplex from bypass

Not from bypass to finisher

Paper capacity exceeded.

Remve paper from Job sep.

PAPER CAPACITY EXCEEDED.

REMOVE PAPER FROM JOB SEP.

—

This code is not in use.

Job is cancelled.

Exceeded print quantity

limit.

Exceeded pre-registered

printing quantity.

RAM disk error Press GO

MemoryCard err Press GO

Memory Card err Insert again

Insert the same memory card

Format error Memory card

Procedure

Duplex printing is not possible using the Multi-Bypass. Select the drawer for paper

feed.

* If you want to print out on only one side of the paper, first press the Printer key to

switch to the printer mode. Next, select the “GO” command and then press the

Enter key. If you want to switch to and print from a cassette, press the Paper

Select key until the desired cassette is selected and then press the Enter key.

The finisher cannot be used when paper is fed from the Multi-Bypass.

* If you want to have the paper ejected into the Inner tray, first press the Printer key

to switch to the printer mode. Next, select the “GO” command and then press the

Enter key. If you want to switch to and print from a cassette, press the Paper

Select key until the desired cassette is selected and then press the Enter key.

The amount of paper stacked in the optional Job Separator has exceeded the

acceptable capacity. Remove all paper from the Job Separator.

Trouble has occurred within the printer. Contact your service representative or an

authorized service center.

The department code you entered does not match the registered one. Check the

department code that is registered in the printer driver.

The amount of printing accomplished has exceeded the acceptable capacity as set

under copy management. In order to print further, change the copy management

setting in the printer.

<15 ppm

copier

A read- or write-error has occurred on the RAM disk. Press the Start key.

<20 ppm

copier

A read- or write-error has occurred on the RAM disk. First press the Printer key to

switch to the printer mode. Next, select the “GO” command and then press the

Enter key.

<15 ppm

copier

A read- or write-error has occurred in the Memory Card (CompactFlash). Press the

Start key.

<20 ppm

copier

A read- or write-error has occurred in the Memory Card (CompactFlash). First

press the Printer key to switch to the printer mode. Next, select the “GO” command

and then press the Enter key.

The Memory Card (CompactFlash) was removed during operation under the menu

for printer-related settings. Reinsert the Memory Card.

The Memory Card (CompactFlash) could not be detected during an operation in

which the printer was reading data from that card. Reinsert the Memory Card.

Initialization of the Memory Card (CompactFlash) currently inserted is necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oce OP15 Operations Guide Printing System Set-up Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info