Bedienungsanleitung Oce OP20 Operations Guide Printing System Functions (Seite 56 von 87) (Englisch)

47525

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

3-10

3. Printer Driver for Windows 95/98

● Staple

It is possible to staple your copy sets if the optional Finisher is installed.

* Stapling is only available with 20 ppm copiers.

* The following settings are required before stapling is possible:

(1) “Installable Options” setting in the “Device Options” Tab

Select “Finisher” as the “Output Device” setting and “RAM Disk” under “Optional Disk”.

(2) “Printer Features” setting in the “Device Options” Tab

Select “Finisher” as the “Paper Destination” setting and “Temporary” under “Job Spooling”.

* Paper sizes, types and source of paper feed that are acceptable for stapling are as follows:

Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Tabloid (11" x 17"), A3, A4, JIS B4 and JIS B5

Paper types: Plain, Letterhead, Recycled and Color

Source of paper feed: Any tray EXCEPT the Bypass Tray

● Management Code

This setting is used when Copy Management is turned ON in the printer. If the Management code that you selected from the dropdown

list here and that selected in the printer itself do not match, printing will not be possible.

* If Copy Management is turned ON and this setting does not match the setting made in the printer itself, it will not be possible to make

test prints. Thus, when you install the printer driver, you will need to check the Copy Management settings and make a test print

AFTER the installation procedure is complete.

* When Copy Management is turned ON, even if you send a print command with a DOS “COPY” command, printing will not be possible

if you do not use a printer driver.

● Edge Smoothing

Turning this setting “On” allows the jaggies that appear around the edge of text and graphics to be evened out through the smoothing

process.

● Page Policy

Perform this setting in conjunction with the settings to be made under “Paper source” on page 3-6.

[Auto Size Select] ......................Select this setting when you want to select the source of paper feed according to the type of paper

(you are going to select “AutoSelect Tray” under “Paper source”).

[Cassette Base] .........................Select this setting when you want to select the source of paper feed according to the tray under

“Paper source”.

* If you are going to select “AutoSelect Tray” under “Paper source”, be sure to select “Auto Size Select” here or there is a possibility that

printing will be accomplished onto paper that is difference the expected.

● Job Spooling

When you want to print out more than one set of the same documents, it is possible to have them sorted and ejected one set at a time.

[None] .........................................Does not sort.

[Temporary] ............................... Sorts and prints in order of sets: Set 1, Set 2, Set 3, etc.

* It is necessary to create a RAM disk. (Refer to “● Optional Disk” below.)

* If you selected any of the “Staple” settings above, it is necessary to select “Temporary” here.

■ Installable options

Perform the settings here whenever you add optional equipment. The functions of the optional equipment will only be available to the

printer after you have completed the setting here. Select the desired optional equipment here and then change the setting in the field

under “Change setting for: xxxx”. The optional equipment available for selection are as follows:

● Optional Feeder

Perform this setting according to the installed Option Cassette.

● Output Device

Perform this setting when the optional Job Separator or Finisher (only available with 20 ppm copiers) are installed.

● Duplex Unit

Perform this setting when the optional Duplex Unit (only available with 20 ppm copiers) is installed.

● Optional Disk

Perform this setting when you want to create a RAM disk. Refer to “Chapter 1, 3-2 RAM Disk” on page 3-1 for more detailed information

on creating a RAM disk.

* In order to create a RAM disk, it is necessary to increase the memory capacity of your printer. After increasing memory, perform the

setting here according to the “VM Option” setting below.

● VM Option

Perform this setting according to the amount of memory in your printer. If a mistake is made in this setting, there is a possibility that

printing will not be accomplished properly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oce OP20 Operations Guide Printing System Functions Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info