Bedienungsanleitung Oce OP20 Operations Guide Printing System Functions (Seite 61 von 87) (Englisch)

47525

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

4-4

4. Printer Driver for WindowsNT

■ Media:

Saves on toner. Setting can be made in the “Change ‘Media’ Setting” area. The factory default setting is “Off”.

■ Paper/Output:

Allows you to select the location of ejection and whether you want to staple the sets or not when the optional Job Separator or Finisher is

installed. Selection can be made in the “Change ‘Paper/Output’ Setting” area.

[Inner Tray] .................................Copies will be ejected onto the Inner tray.

[Job Separator] .........................Copies will be ejected into the optional Job Separator.

[Finisher (Staple Off)] ...............Copies will be ejected into the optional Finisher. (Only available in the 20 ppm copiers)

[Finisher (Staple On)]................Copies will be stapled and ejected into the optional Finisher. (Only available in the 20 ppm copiers)

* Paper sizes are acceptable for use with the Job Separator are as follows:

Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), Statement (5 1/2" x 8 1/2"), A3, A4, A5, Folio (210 mm x 330

mm), JIS B4 and JIS B5

* Paper sizes and source of paper feed that are acceptable for use with the Finisher are as follows:

Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), A3, A4, Folio (210 mm x 330 mm), JIS B4 and JIS B5

Source of paper feed: Any tray EXCEPT the Bypass Tray

* Paper sizes and source of paper feed that are acceptable for stapling are as follows:

Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), A3, A4, JIS B4 and JIS B5

Source of paper feed: Any tray EXCEPT the Bypass Tray

Note

If you want to staple your printed sets, be sure to use a Collator driver. (Refer to “Collator driver” on page 1-1.)

■ Print Quality (Management Code)

This setting is used when Copy Management is turned ON in the printer. If the “management code” selected in the “Change ‘Print Quality’

Setting” area does not match the one set on the printer, printing will not be performed. If “Management Code Off” is selected, the number

of prints for each department will not be checked. The factory default setting is “Management Code Off”.

* If Copy Management is turned ON and this setting does not match the setting made in the printer itself, it will not be possible to make

test prints. Thus, when you install the printer driver, you will need to check the Copy Management settings and make a test print AFTER

the installation procedure is complete.

* When Copy Management is turned ON, even if you send a print command with a DOS “COPY” command, printing will not be possible

if you do not use a printer driver.

4-4 Document Options (Universal Driver)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oce OP20 Operations Guide Printing System Functions Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info