Bedienungsanleitung Oce OP20 Operations Guide Printing System Functions (Seite 67 von 87) (Englisch)

47525

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

4-10

4. Printer Driver for WindowsNT

■ Staple

It is possible to staple your copy sets if the optional Finisher is installed.

Select the desired function here and then change the setting in the field under “Change 'Paper Destination' Setting”.

* Stapling is only available with 20 ppm copiers.

* The following settings are required before stapling is possible:

(1) “Installable Options” setting in the “Device Settings” Tab under “Properties” (Refer to step 4 on page 4-1 for information on accessing

“Properties”.)

Select “Finisher” as the “Output Device” setting and “RAM Disk” under “Optional Disk”.

(2) “Printer Features” setting

Select “Finisher” as the “Paper Destination” setting and “Temporary” under “Job Spooling”.

* Paper sizes, types and source of paper feed that are acceptable for stapling are as follows:

Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Tabloid (11" x 17"), A3, A4, JIS B4 and JIS B5

Paper types: Plain, Letterhead, Recycled and Color

Source of paper feed: Any tray EXCEPT the Bypass Tray

■ Management Code:

This setting is used when Copy Management is turned ON in the printer. If the “management code” selected in the “Change ‘Management

Code’ Setting” area does not match the one set on the printer, printing will not be performed. If “Off” is selected, the number of prints for

each department will not be checked. The factory default setting is “Off”.

* If Copy Management is turned ON and this setting does not match the setting made in the printer itself, it will not be possible to make

test prints. Thus, when you install the printer driver, you will need to check the Copy Management settings and make a test print AFTER

the installation procedure is complete.

* When Copy Management is turned ON, even if you send a print command with a DOS “COPY” command, printing will not be possible

if you do not use a printer driver.

■ Edge Smoothing:

Turning this setting “On” allows the jaggies that appear around the edge of text and graphics to be evened out through the smoothing

process.

■ PagePolicy:

Perform this setting in conjunction with the settings to be made under “Paper source” on page 4-6.

[Auto Size Select] ......................Select this setting when you want to select the source of paper feed according to the type of paper

(you are going to select “Automatically Select” under “Paper source”).

[Cassette Base] .........................Select this setting when you want to select the source of paper feed according to the tray under

“Paper source”.

* If you are going to select “Automatically Select” under “Paper source”, be sure to select “Auto Size Select” here or there is a possibility

that printing will be accomplished onto paper that is difference the expected.

■ Job Spooling:

When you want to print out more than one set of the same documents, it is possible to have them sorted and ejected one set at a time.

[None] ........................................Does not sort.

[Sort] .........................................Sorts and prints in order of sets: Set 1, Set 2, Set 3, etc.

* It is necessary to create a RAM disk. (Refer to page 4-11.)

* If you selected any of the “Staple” settings above, it is necessary to select “Temporary” here.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oce OP20 Operations Guide Printing System Functions Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info