Bedienungsanleitung Oce OP30C Printing System Functions (Seite 86 von 90) (Englisch)

46807

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

11-7

11. Printer Driver for Macintosh

■ Paper Destination:

Specifies the location of ejection for print jobs.

[Inner Tray] ................................. Copies will be ejected onto the Inner tray.

[Side Tray] .................................. Copies will be ejected into the side tray.

[Finisher (Face-Up)] .................. Copies will be ejected into the upper tray of the optional Finisher.

[Finisher (Face-Down)] ............. Copies will be ejected into the lower tray of the optional Finisher.

■ Staple:

It is possible to staple your copy sets if the optional Finisher is installed.

* The following settings are required before stapling is possible:

(1) Change the “Installable Options” setting in step 10 on page 11-3 to the following.

Select “Finisher” under “Output Device”.

(2) Change the “Printer Specific Options” setting on page 11-6 to the following.

Select “Finisher (Face-Down)” under “Paper Destination”.

■ Punch:

When the optional Finisher is equipped with a Punch Unit, it is possible to have holes punched into the finished copies.

* In order to use the Hole Punch function, it is first necessary to perform the following settings.

(1) Change the “Installable Options” setting in step 10 on page 11-3 to the following.

Select “Finisher” under “Output Device”.

(2) Change the “Printer Specific Options” setting on page 11-6 to the following.

Select “Finisher (Face-Down)” or “Finisher (Face-Up)” under “Paper Destination”.

■ Management Code:

This setting is used when Copy Management is turned ON in the printer. If the Management code that you selected from the dropdown list

here and that selected in the printer itself do not match, printing will not be possible.

■ 180 Rotate:

Selecting this option prints upside down.

■ Barcode:

If “Temporary Job” or “Permanent Job” is selected under “Job Storage”, you can select here whether or not to have a barcode printed onto

the printed pages. This barcode can be read using the optional Barcode Reader in order to print out the corresponding data that is stored

in the printer.

[First Page Only]........................The barcode will be only printed onto the first page.

[All Pages] .................................. The barcode will be printed onto all printed pages.

[Do not print Barcode] .............. The barcode will be not be printed at all.

■ Barcode ID:

Select “On” if you want to have the barcode ID printed.

■ Barcode Position:

Designates the location on the page where the barcode will be printed. It is possible for you to select both the location (from among “Upper

Left”, “Upper Right”, “Lower Left” and “Lower Right”) and the orientation of the barcode on the page.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oce OP30C Printing System Functions Seite 86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info