Bedienungsanleitung Oceanic BUD (Seite 19 von 24) (Englisch)

550354

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

BUD OPERATING MANUAL

WARNING: If damage, moisture, or corrosion is found, return your BUD to an Authorized Oceanic Dealer, and

DO NOT attempt to use it until it has received factory prescribed service.

Battery Installation

• Slide a new 3 volt type CR2430 Lithium Battery, negative side down into the Battery Compartment. Slide it in from the left

side (Fig. 48) and ensure that it slides under the contact clip on the lower/right rim of the cavity.

• Lightly lubricate the new Cover O-ring* with silicone grease and place it on the inner rim of the Battery Cover. Ensure that it

is evenly seated (Fig. 49).

*The O-ring must be a genuine Oceanic part that can be purchased from an Authorized Oceanic Dealer. Use of any

other O-ring will void the warranty.

• Carefully place the Battery Cover (with O-ring) into position on the rim of the Battery Compartment, then press it evenly and

completely down into place.

• Maintain the Battery Cover securely in place and turn it counter clockwise 10 degrees using the special Battery Cover tool

(Fig. 50A), or by pushing the lower portion to the right while pushing the upper portion to the left (Fig. 50B).

Testing

• Observe the LCD display to ensure it is consistently clear and sharp in contrast throughout the screen.

• Set the Date and Time.

• Verify all Set Points prior to diving.

If any portions of the display are missing or appear dim, or if a Low Battery Condition is indicated, return

your BUD to an Authorized Oceanic Dealer for a complete evaluation before attempting to use it.

ALTITUDE SENSING AND ADJUSTMENT

Altitude (i.e., ambient pressure) is measured upon activation and every 15 minutes until a dive is made.

> Measurements are only taken when the unit is dry.

> Two readings are taken, the second reading 5 seconds after the ﬁrst. The readings must be within 1 foot (30 cm) of each other to record that ambient

pressure as the current Altitude.

> No adjustments are made during any time that the Wet Contacts are bridged.

> When diving in high altitude waters from 3,001 to 14,000 feet (916 to 4,270 meters), the BUD automatically adjusts to these conditions providing

corrected Depth, and reduced No Deco and O2 Times at intervals of 1,000 feet (305 meters).

> At Sea Level, calculations are based upon an Altitude of 6,000 feet.

> All adjustments for Altitudes greater than 11,000 feet (3,355 meters) are then made to allowable dive times for 14,000 feet (4,270 meters).

> The BUD will not function as a Dive Computer above 14,000 feet (4,270 meters).

Fig. 48 - BATTERY INSTALL

Fig. 49 - COVER O-RING

Fig. 50B - COVER

INSTALL (using thumbs)

Fig. 50A - COVER

INSTALL (using tool)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oceanic BUD Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oceanic BUD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info