738313

Octane Fitness XR6000S Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Complete Console Setup according to instructions found in
the Console Guide
and Setup Instructions
(Part Number 111289-001 – Standard Console or
Part Number 111768-001 – Smart Console).
Use a #2 Phillips screwdriver to attach back cover to console with C-1
(quantity 6); tighten. Reattach mast cover to mast with screw removed in
step C-5, taking care to tuck cables out of the way before securing to mast.
(Shown in Section C illustration).
Level machine; adjust and lock levelers using 17mm wrench.
Make sure nut is tight.
F
Complete Setup &
Level Machine
If you have the optional Personal Viewing System (PVS) accessory, refer to Personal Viewing System (PVS) Assembly Instructions
located in the box with your PVS accessory, then return to these instructions to complete final assembly.
If you have the optional
900 MHz accessory, refer to 900 MHz Assembly Instructions located in the box with your 900 MHz accessory,
then return to these instructions to complete final assembly.
STOP
D
Connect Battery & Attach Moving Handlebars
With upper pedal links positioned on front side of mast post, attach foot rest bracket to
mast with screw B-9 (quantity 4); tighten all 4 screws with 5mm hex wrench until tight.
To install foot pedal:
Place wave washer B-10 (quantity 1) on pedal crank axle, then press lower end of foot pedal
onto pedal crank axle. (Use a rubber mallet to assist if needed.)
Place washer B-5 onto screw B-11 (quantity 1 each). Insert B-11/B-5 assembly into lower
hub and into pedal crank axle; tighten with 6mm hex wrench to 19 ft-lb.
Press cap B-12 into place in lower foot pedal hub.
Place cap B-13 onto screw B-11 (quantity 1 each). Insert B-11/B-13 assembly through upper
pedal link into upper foot pedal hub; tighten with 6mm hex wrench to 19 ft-lb.
Repeat steps 2-4 for second foot pedal.
For xR6000s Only: Place side step next to one side of the unit with back of side step aligned
with back of foot platform. Carefully tip unit away from you and push side step under rail of
unit. Lower unit onto side step channel. Repeat for second side step.
Assembly Instructions
Latin America/Asian Pacific
001-763-757-2662
Europe/Middle East/Africa
31-10-2662412
Questions?
octanefitness.com
113201-001 REV E Page 2/2
USA & Canada
888-OCTANE4
©2020 Octane Fitness. All rights reserved.
E
Attach Foot
Pedals & Foot Rest
Use #2 Phillips screwdriver to remove 4 screws securing battery access panel.
Use flat screwdriver at the side corner seams to gently unsnap bottom of panel;
remove from unit and set aside with screws.
Use #2 Phillips screwdriver to remove 1 screw securing each crank arm cover; turn
each cover counter-clockwise to remove and set aside with screws.
Connect cable on battery to cable in base (if you have not already done so during
installation of PVS or 900MHz accessory). Connect power cord to wall socket.
To install moving handlebar:
Place washer B-5 on bolt B-4 (quantity 1 each); attach moving handlebar
at hub with B-4/B-5 assembly and tighten with 13mm wrench to 19 ft-lb.
Position pedal crank axle at top-most position. Insert arm link of moving handlebar
into arm link bracket, aligned with hole #1 on bracket. From the outside toward the
center of the unit, insert screw B-6 (quantity 1) into arm link bracket and through arm
link and nut B-7; tighten with 13mm wrench to 17 ft-lb. For a longer reach, use hole #2 in
the arm link bracket. You must use the same hole (#1 or #2) on both handlebars.
Position large arm pivot cover around handlebar shaft and slide down to hub,
inserting posts on pivot cover into square holes in hub. Use #2 Phillips screwdriver
to secure large arm pivot cover to hub with B-8 (quantity 1). Press tabs of small arm
pivot cover into slots in large arm pivot cover. Use #2 Phillips screwdriver to secure
small arm pivot cover with B-8 (quantity 1).
Complete steps 4-6 for second moving handlebar.
Verify that you have properly connected the battery (per step 1). Then, move
handlebars back and forth to check console power (not shown).
For standard console: Verify console powers up and stays lit for more than 5
seconds. For smart console: Press power switch to start console and verify
xR6000 landing screen displays.
Position each crank arm cover, turning it clockwise to lock into place, then secure
using #2 Phillips screwdriver and screws removed in step 2.
Position bottom of battery access panel and snap into place, then press top
of panel into place. Use #2 Phillips screwdriver and secure with
4 screws removed in step 1.
cables
not
shown
Install Side Steps
(xR6000s only)
(Console and mast
not shown)
snap
apart
here
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Octane Fitness XR6000S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info