Bedienungsanleitung OK OAC 2221 (Seite 22 von 32) (Deutsch, Englisch)

783003

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

INSTALLATION

Placement

When choosing an installation place, consider following points:

• Observe all safety warnings!

• Ensure the minimum surrounding distance in every direction of 30 cm and 100 cm to other electrical

products.

• Keep a surrounding distance of minimum 50 cm around the outside of exhaust wall outlet and protect

it from entering objects and moisture.

• Make sure the wall behind the product is an exterior wall not a divider and the drill holes can be made

in a safe way, not obstructed by hidden objects in the wall.

• Ensure that a suitable power outlet is within reach at the desired location and remains accessible after

installation.

• Consider that during dehumidifying operation water is collected inside the product, which must be

continuously drained through a connected drainage hose into a suitable container or a nearby drain.

• Ensure there are no obstacles obstructing the airow.

Air exhaust

The exhaust hose and adaptor must be installed or removed in accordance with the usage mode:

• COOL, AUTO mode: install exhaust hose.

• FAN, DEHUMIDFY mode: remove exhaust hose.

Wall (Parts: N, O, P, Q)

Fig. 1 Screw the wall adapter and exhaust adapter onto each side of the exhaust hose. Connect

the exhaust adapter to the air exhaust of the product.

Fig. 2 Use the wall connector as pattern to mark the hole spacing on the wall. Drill the holes

with a suitable power tool. Free the holes from dust and mount the wall connector using

supplied screws and plugs. Connect the wall adapter to the wall connector.

Note:

• The exhaust hose can be expanded and compressed, but for optimal performance, keep

the exhaust length to a minimum.

• Do not extend the exhaust hose.

• Avoid over-bending.

• Observe the decommissioning instructions in the respective section, if the product is

not to be used for a longer period of time.

Window (Parts: N, O, R)

Fig. 3 The exhaust hose can be attached to an open or tilted window alternatively. Screw the

window outlet adapter onto the open end of the exhaust hose.

Note: Material necessary for attachment and sealing is not provided but must be

purchased in special shops.

Drainage hose

Fig. 4 The drainage hose is used to drain water from the upper drain outlet.

1. Slide the drainage hose as far as possible onto the outlet.

2. Lead the other end of the drainage hose into a suitable container or a nearby drain.

Notes:

• Depending on the set modus the water is either drained directly or collected in an internal

tank. Drain the water respectively.

• Always cover the drain outlets when not in use.

• Observe the decommissioning instructions in the respective section, if the product is not

to be used for a longer period of time.

IM_OAC2221_161201_V04_HR.indb 22 1/12/16 4:31 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

OK OAC 2221 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info