Bedienungsanleitung OK OAC 2221 (Seite 27 von 32) (Deutsch, Englisch)

783003

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Fig. 10 Setting the timer

The timer switches the product on or into standby when a user-dened time has elapsed.

When switching on, the last mode and setting will be used. The set durations will be counted

down immediately after the input without correlation to the contrary time setting.

1. Press the timer program button TIMER at the product or the specic TIMER ON/OFF

button at the remote control to enter timer setting for either the auto-on or auto-standby

timer. The respective indicator for each setting will light up.

2. Press the / buttons or the specic TIMER ON/OFF button at the remote control as

often as necessary to set a time from 0.5 to 24 hours.

3. The setting will be saved after 5 seconds without input.

Examples:

• To have the product switched o after 1 hour and on again after another 1 ½ hours, set the

auto-o time to 1.0 h and the auto-on time to 2.5 h during operation.

• To have the product switched on after 8 hours and o after another 8 hours, set the auto-

on time to 8.0 h and the auto-o time to 16.0 h while in standby.

Notes:

• The adjusting increments are 0.5 hours up to 10 hours, then 1 hour up to 24 hours.

• The respective indicator will be lit, when a time is set.

• Switching the product on or into standby manually will cancel the timer setting.

• The timer settings will be lost once the respective actions were conducted and the time

needs to be set again.

• The timer setting will be lost in case an error occurs (see protection and error codes).

Preprogramming a function

By pushing the SHORTCUT button any function and temperature can be saved and recalled.

1. Choose your desired function e.g. using the MODE, TEMP / or / and FAN buttons, etc.

2. Press and hold SHORTCUT button until the display ashes one time to save the setting.

3. The preset setting can be recalled anytime and from any mode by simply pushing the SHORTCUT

button.

Fig. 11 WATER DRAINAGE

Water is only collected during automatic AUTO, cooling and dehumidifying mode .

During dehumidifying mode water is drained immediately through the upper drain outlet

and the drainage hose must be continuously connected. The water is drained through the

hose into a suitable container or nearby drain.

WARNING – Danger of ooding! Do not leave the product unattended when draining to an

external container! Empty the container frequently to avoid spilling over and water damage.

During automatic AUTO and cooling mode water is collected in an internal tank, which

must be drained when full. In this case the product will emit an audible signal, while the

display on the control panel is showing the protection code P1. The cooling process will stop

until the water is drained and the product restarted, while the fan remains running.

1. Disconnect the product from the power supply.

2. Place the product with the lower drain outlet above a suitable container or a drain.

3. Remove the cover of the lower drain outlet.

4. Attach the cover of the outlet again, when all water is drained.

5. Connect the plug to a suitable socket.

6. The product is ready to be switched on.

IM_OAC2221_161201_V04_HR.indb 27 1/12/16 4:31 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

OK OAC 2221 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info