Bedienungsanleitung OK OSF 4332 (Seite 11 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch)

783092

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

ASSEMBLING AND MOUNTING

1 Assemble the two foot parts crosswise. Remove the four screws from the foot parts.

2 Use the four screws to mount the extension pole onto the feet. Then remove the height adjustment

ring.

3 Slide the stand cover over the extension pole onto the feet. Pull out the extension pole and secure

it by installing and fastening the height adjustment ring.

4 Attach the motor unit to the extension pole and secure it with the screws. Before secure it, the

height of the fan can be adjusted individually, by inserting / extracting the extension pole.

5 Remove the propeller nut and the plastic nut from the motor unit. Attach the rear guard to the

motor unit. The handle on the rear guard must point upwards and the dowel pins must t into the

intended holes.

6 Secure the rear guard with the plastic nut.

7 Slide the fan blade onto the motor shaft so that the pin locks to the groove. Secure the fan blade by

tightening the propeller nut onto the shaft.

8 Open the clips on the front guard. Hook the front guard onto the rear guard, thereby aligning the

screw holes at the bottom of the guards.

9 Install the screw and nut to lock the guards. Make sure all the clips are closed.

10 Place on a stable level surface. Set the desired angle and height.

OPERATION

11 Plug in the product.

12 Press the ON/OFF to switch on the fan. Press SPEED repeatedly to cycle through the fan speeds

(L=Low; M=Medium; H=High). Alternatively you can use the button on the remote control to

select the speed. Press the button to turn on/o the product.

13 Press button on the remote control for timed operation. Press the button repeatedly to set

the hours (1, 2, 4 hours) after which the fan should turn o.

14 Press the OSCILLATION / SWING knob to activate oscillation function.

Caution

• The product may only be connected to the mains once it has been completely assembled.

• The product must not be disassembled during operation, general care, cleaning and user

maintenance.

• The product may never be operated without the stand or in a horizontal position.

• Switch o and disconnect the product before adjusting height or desired angle.

• The guard must be completely closed when operating the product.

• During operation, do not put ngers or other objects in the guard.

• Unplug the product if it is not used for some time.

CHANGING BATTERIES

15 Open the battery compartment of the remote control. Insert 2 batteries (not included) of type

LR03 (AAA) observing the + and – polarities as indicated on the batteries and inside the battery

compartment. Close the battery compartment.

IM_OSF4332-W-RC_OSF-433- B-RC _191104_V05_HR.indb 11 4/11/19 5:22 pm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

OK OSF 4332 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info