Bedienungsanleitung OK OWM 5212 D (Seite 21 von 30) (Deutsch, Englisch)

783122

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

INSTALLATION

Note: The washing machine is equipped with power cord and plug and needs sewage

and tap water connections. Before installation, make sure that suitable connections are

at the desired place of installation.

Consider the dimensions (chapter Technical data) of the product for placing and

installation.

Caution

• Before initial operation the transport restraints must be removed from the backside

of the unit. Operating the washing machine with mounted transport restraints leads

to serious damages.

• Keep the transport restraints for later use. Never transport the device without

correctly mounted transport restraints!

1 Loosen the four transport restraints with a wrench (13 mm) and unscrew them

completely. Insert the 4 supplied blind plugs in the holes.

2 Place the washing machine on an even, horizontal and steady surface. For levelling,

the feet are adjustable and can be screwed in or out.

• If the feet cannot be loosened by hand, use pliers.

• Turn the feet to the right to screw them in and to the left to unscrew them.

• Use a spirit level to check whether the appliance is levelled. If the appliance is

not standing horizontally or is tilted, the feet must be adjusted again.

• If the unit is levelled and does not tilt, tighten the nuts with an open-end wrench.

Note:

Note the following, when placing the appliance on a platform:

The appliance might move during spinning and could fall of a platform. To prevent

this, the feet must be secured with retaining tabs (available in specialized stores).

3 The washing machine must be connected to a drain.

• The drain hose is already ﬁxed to the sewage connection. Pull the hose out of

the clamps and unwind it.

• Connect the other end to the drain pipe (option A or B). Observe the max.

height of the hose end.

Note:

• To avoid leakage, a hose clamp should be used to correctly install the outlet

hose.

• Suitable hose holders are available as optional accessories.

4 Connect the water inlet to the water system (3/4“) using the supplied hose and

make sure that everything is connected correctly and ﬁrmly. The water pressure

must be between 0.05MPa and 1 MPa. A pressure reducing valve must be used if

the water pressure exceeds 1 MPa. The correct installation of the water connection

should be checked on a regular basis.

Note:

• If the water pipes are new or have not been used for an extended period of time,

allow a certain amount of water to drain until you are sure that the water is clear

and free of foreign objects.

• If this point is not observed, there is a risk that the water inlet will become

clogged and the unit will be damaged.

5 Plug the mains plug into a suitable socket.

IM_OWM 5212 D_A5_DE_EN_210218_V04_HR.indb 21IM_OWM 5212 D_A5_DE_EN_210218_V04_HR.indb 21 18/2/2021 3:49 PM18/2/2021 3:49 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

OK OWM 5212 D Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info