Bedienungsanleitung Okbaby Eggy Pack (Seite 7 von 51) (Alle Sprachen)

773008

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

8 9

ENGLISH

Eggy Pack Rear child‘s seat Eggy Pack Rear child‘s seat

Warnings

1) WARNING: Do not place any additional baggage on the seat. Any

additional baggage must be placed on the opposite side of the

bicycle with respect to the seat. For example: if the seat is in the

rear of the bicycle, use a front bag carrier and vice versa

2) WARNING: Do not modify the seat.

3) WARNING: Riding the bicycle may be different with a child in the

seat, especially regarding balance, steering and braking.

4) WARNING: Never park the bicycle leaving the child unattended

in the seat.

5) WARNING: Do not use the seat if any part is missing or broken.

Mounting and assembling the child seat

Illustrations 1-2:

Insert the right and left jaws (4) (5) aligning them in correspondence

to the right and left sides between plate and jaws. Push both jaws

inwards as far as possible.

Illustration 3:

Insert the handwheel (8) in the threaded bar mounted on the fasten-

ing plate (6).

Illustration 4:

Turn the handwheel (8) clockwise whilst pushing both jaws (4,5)

inwards until they start to move.

Illustration 5:

Use the screws (7) to fasten the handwheel (8) to the threaded rod.

Illustrations 6-7:

Place the child seat on the bicycle carrier rack and block in place

by turning the handwheel (8) clockwise until the jaws (4,5) are

completely closed. To release the seat from the carrier rack, turn the

hand wheel (8) counter-clockwise while pressing down on the red

lever (fig. 6,A).

WARNING: Close the jaws firmly in place and check they remain

tight on a regular basis.

NOTE: Refer to the installation diagram (illustration 8) when fitting

the child seat on the carrier rack to make sure it is positioned cor-

rectly. The barycentre symbol on the side of the seat must be within

a maximum distance of 10 cm with respect to the centre of the

wheel. We recommend fitting the child seat as close as possible to

the bicycle seat.

Illustration 9:

Bind the fastening block safety strap to the bicycle seat post, secur-

ing the excess strap with the stop (fig. 10,A).

WARNING: always use the safety belts!

WARNING: always use the belt fastener to prevent the excess

section of the belt coming into contact with the wheels or other

mechanical moving parts on the bicycle.

Using the seat:

Illustrations 11-12:

Fastening the footrests: Place the footrest marked “SX” in the high-

est position of the seat’s left leg. Insert the regulating pin marked

“SX” from the outside of the child seat inwards. Repeat the opera-

tions for the right footrest and relative regulating pin, marked “DX”.

To adjust the height of the footrests (9), rotate the regulating pin

(10) upwards; once you have found the desired position, turn the

pin downwards to fix the footrests in place.

Illustration 13:

Fastening and unfastening the child’s feet: to secure the child’s feet,

secure the strap on the external side of the foot in the clasp on the

rest.

Always make sure your child’s feet are well fastened to the foot-

rests. The safety belt is long for easy adjustment.

Illustration 14:

Setting the height of the belt: remove the belts to adjust height,

inserting the clasp behind the back through the slot as required (fig.

14-A). Choose the upper or lower openings to fix the belts based on

the child’s height. Setting belt length: modify belt length by sliding

the buckles. The belts must be fastened firmly without them being

too tight for the child. Fastening the belts: connect the belt clasp.

Check that the belt clasp clicks shut properly by pulling on the belt.

Illustration 15:

To unfasten the belt, simultaneously press the two buttons (front

and rear) found on the clasp.

Maintenance

1) Clean the seat, the padding and the belts with warm water and

a mild detergent. Do not use solvents or abrasive or corrosive

detergents. Leave the padding to dry in the open air. Do not

iron out.

2) Seat repairs and replacement of damaged components must

only be carried out by authorized personnel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Okbaby Eggy Pack Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info