492994
52
Zoom out
Zoom in
Vorherige Seite
1/94
Nächste Seite
Menu functions > 52
FRAME TYPE AUTO / 802.2 / 802.3 /
ETHERNET II / SNAP
Applies to C331 and C531/ES5431 only.
Selects the Ethernet MAC layer frame type.
Display Condition: Netware should be enabled.
IP ADDRESS SET AUTO / MANUAL Specifies whether IP address allocation is automatic
(DHCP) or manually assigned.
IPV4 ADDRESS xxx.xxx.xxx.xxx Current assigned IP address. To change, press OK and
use Menu buttons to increment 1st octet, then press
OK again to move on to next octet. When 4th octet has
been set, press OK again to register new address.
SUBNET MASK xxx.xxx.xxx.xxx Current assigned subnet mask. To change, proceed as
above.
GATEWAY ADDRESS xxx.xxx.xxx.xxx Current assigned gateway address. To change, proceed
as above.
WEB ENABLE / DISABLE Enables or disables Web config. facility.
TELNET ENABLE / DISABLE Enables or disables Telnet config. facility.
FTP ENABLE / DISABLE Enables or disables communication via FTP.
IPSEC ENABLE / DISABLE Applies to C331 and C531/ES5431 only.
Sets Enable/Disable of IPSec. Enable via the web.
Enable: IPSec is available.
Disable: IPSec is not available.
SNMP ENABLE / DISABLE Enables or disables SNMP protocol.
NETWORK SCALE NORMAL / SMALL Selects network size.
When NORMAL is selected, printer can work effectively,
even when connected to a HUB that has a spanning
tree
feature. However, printer start up time gets longer
when computers are connected with two or three small
LANs.
When SMALL is selected, computers can cover from two
or three small LANs to a large LAN, but may not work
effectively when connected to a HUB that has a
spanning tree feature.
HUB LINK SETTING AUTO NEGOTIATE
100BASE-TX FULL
100BASE-TX HALF
10BASE-T FULL
10BASE-T HALF
Sets full or half duplex for communication via a network
hub.
When AUTO is set, negotiation is done automatically.
TCP ACK TYPE 1
TYPE2
This setting determines whether the network card in
the Printer/MFP will acknowledge every TCP packet or
whether it will delay it’s acknowledgement until
multiple packets have been received.
When Type 1 is set the Printer/MFP will respond to
every TCP packet with an ACK packet.
When Type 2 is set the Printer/MFP will delay it’s TCP
ACK response.
In most environments the default TCP ACK setting
should be OK, however changing this setting may be
beneficial when a connection problem (e.g your printing
job incompletely terminates) occurs if it takes a long
time to interpret/print your job.
FACTORY DEFAULTS EXECUTE Reloads the settings present when the unit was setup
by the manufacturer.
ITEM SETTINGS EXPLANATION
52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Oki C331 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Oki C331

Oki C331 Bedienungsanleitung - Deutsch - 104 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info