665223
28
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
Menu functions > 28
PS Setup Network
Protocol
ASCII/RAW Specifies PS communication protocol mode of data from
NIC port.
(In RAW mode, Ctrl-T is invalid). PS models only.
Parallel
Protocol
ASCII/RAW Specifies PS communication protocol mode of data from
Centronics port.
(In RAW mode, Ctrl-T is invalid). PS models only.
USB
Protocol
ASCII/RAW Specifies PS communication protocol mode of data from
USB port.
(In RAW mode, Ctrl-T is invalid). PS models only.
PCL Setup Font Source Resident Specifies the location of PCL default font.
Font
Number
I0 ~ I90 Sets the PCL font number.
The valid range of this variable changes depending on the
FONT SOURCE setting at the time. If the default font is
set for FONT SOURCE, the number starts at 0. If it is not,
the number starts at 1. The maximum value is equal to
the number of fonts installed in FONT SOURCE.
Font Pitch 99.9 CPI
~
10.00 CPI
~
0.44 CPI
Width of the PCL default font in characters per inch (CPI).
Default font is fixed-pitch, scalable font.
The value of pitch is displayed down to the second
decimal place.
Displayed only when the font selected in Font No. is a
fixed-spacing, scalable font.
Symbol Set PC-8 Sets the symbol set of PCL (see machine operator panel
for complete list).
A4 Print
Width
78 column
80 column
Sets the number of characters for A4 paper.
Auto LF.
This is for 10-CPI characters when Auto CR/LF Mode is set
to OFF.
This menu is enabled only when A4 paper is selected in
the menu that sets the print width of A4 paper in portrait
orientation.
Usually, such A4 paper print width is set slightly narrower
than 8 inches (about 7.93 inches).
This setting cannot print 80 10-cpi characters (only prints
up to 78 10-cpi characters). 80 characters set at A4 Print
Width widen the right and left margins.
A PCL command selects or selects/deselects Auto CR/LF
mode.
White Page
skip
On/Off Sets whether to eject a page without any data to print
(blank page) upon reception of FF command (OCH) in PCL
Mode. OFF: Ejecting.
CR Function CR/CR+LF Sets action when CR code is received in PCL.
CR: Carriage Return
CR+LF: Carriage Return and Line Feed
LF Function LF/LF+CR Sets action when LF code is received in PCL.
LF: Line Feed
LF+CR: Line Feed and Carriage Return
Print Margin Normal
1/5 inch
1/6 inch
Sets a non-printable area of paper.
The width of the area along the right and left sides of
paper (left and right sides depend on paper orientation).
NORMAL: PCL emulation compatible, approximately 1/
4~1/4.3INCH (depending on paper) is outside the
printable area.
ITEM SETTINGS EXPLANATION
28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Oki C700 series wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Oki C700 series

Oki C700 series Bedienungsanleitung - Deutsch - 75 seiten

Oki C700 series Bedienungsanleitung - Holländisch - 76 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info