Bedienungsanleitung Oki C822dn (Seite 117 von 124) (Englisch)

536475

117

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

- 117 -

6. Troubleshooting

This chapter explains initializing, deleting and updating drivers.

 Initializing

This section explains how to initialize an SD memory card and ash memory and how to reset the

equipment settings to their defaults.

You can delete data or settings stored on the printer to restore the settings to how they were at the

time of purchase.

Note

● In the default settings, [Initialize] cannot be selected because [No] is selected for [Enable Initialization] of

[Storage Setup] in [Boot Menu]. Set [Enable Initialization] of [Storage Setup] in [Boot Menu] to [Yes].

Memo

● In order to access the [Admin Setup] menu, an administrator password is required. The default password is “aaaaaa”.

Initializing an SD memory

card

Carry out initialization of an SD card when

inserting a card that has been used in other

equipment or when the SD Card is not properly

recognized.

An SD memory card is used as storage for

spooling when making multiple copies, for saving

secure print/ encrypted print data, and for form

data and macros. Initialization deletes stored

data.

An SD memory card has three partitions.

They are two Commons, and PCL. When an

SD memory card is initialized, each partition

is respectively divided into the percentage

specied (in the factory default setting,

Common: 30%, Common: 50%, PCL: 20%).

You can also format particular partitions

individually.

If an SD memory card that has been installed to

another device is installed to the printer, or if the

SD memory card installed to the printer cannot

be detected anymore, [Initialize Yes/No] may

appear on the display when the printer is turned

on. In such a case, select [Yes]. (Data stored in

the SD memory card is deleted.)

If [No] is selected and [Service call 067:Error]

appears on the display, turn off the printer and

detach the SD memory card, or turn off the

printer and turn it back on with the SD memory

card left installed, then select [Yes].

Formatting the Entire Area

You can format the entire area of the SD

memory card installed in the printer.

Note

● When you initialize the entire area of an SD memory card,

the following data is deleted.

- Stored job data subject for [Secure Print],

[Encrypted Secure Print] or [Store to SD Card].

- Custom demo data

- Form data

1 Press the <ENTER> button

2 Press to select [Admin Setup] and

then press the <ENTER> button.

3 Enter the administrator password using

the ten-key pad.

The default password is “aaaaaa”.

4 Press the <ENTER> button.

5 Press to select [SD Card Setup] and

then press the <ENTER> button.

6 Make sure that [Initialize] is selected

and then press the <ENTER> button.

7 Make sure that [Execute] is selected

and then press the <ENTER> button.

A message appears notifying you that continuing

will automatically restart the system. Select

[Yes] to continue.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oki C822dn Seite 117

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oki C822dn

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info