Bedienungsanleitung Oki ES4161 (Seite 19 von 203) (Englisch)

492990

Zoom out

Zoom in

Vorherige Seite

1/203

Nächste Seite

Installing Your Machine

-19-

Setup

15 Reinstall the image drum in the

printer:lower it into place in the printer

locating the pegs (1) at each end into

their slots in the sides of the printer

cavity (2).

16 Turn the lever in the direction shown.

 The arrow on the lever should align with the arrow on

the image drum.

 When the toner cartridge is not fully fixed , a decline in

print quality may occur.

17 Close the top cover.

18 Close the scanner unit.

Reference

 Please refer to "Loading Paper" P. 32 for information on

how to load paper into the machine.

Turning On and Off Your Machine

Power Supply Conditions

The power supply must meet the following

conditions:

Note

 If the power supply is unstable, use a voltage regulator.

 The maximum power consumption of this machine is

950W. Ensure that the power supply is sufficient to operate

this machine.

 We do not guarantee the operation where an uninterruptible

power system (UPS) or inverter is used. Do not use an

uninterruptible power system (UPS) or inverter.

Current: 110 - 127VAC

(Range 99 - 140 VAC)

220 - 240VAC

(Range 198 - 264VAC)

Frequency: 50/60 Hz ± 2%

There is a risk of getting

an electric shock and/or

causing fire.

 Be sure to cut off the power supply when attaching

or removing the power supply plug or the earth

wire.

 Be sure to connect an earth wire to the grounding

terminal of exclusive use.

 Please do not connect with the ground of a water

pipe, a gas pipe, and a telephone wire, or lightning

rod without fail.

 Make sure to connect with the ground terminal

before connecting the power cord to the power

supply plug.

 Be sure to perform extraction and insertion of the

power cord with a power supply plug.

 Insert the power supply plug into the wall socket

securely.

 Do not touch the power cord, or machine, if your

hands are wet.

 Install the power cord in a location where it will not

be stepped on, and do not place objects on the

power cord.

 Do not twist, bind, or knot the power cord.

 Please do not use a damaged power cord.

 Do not carry out foot wiring.

 Do not connect this machine and other electric

products to the same wall socket. If connected

simultaneously with an air-conditioner, a copy

machine, shredder, etc., electric noise may

interfere with operation. When the connection with

the same wall socket is unavoidable, please use a

commercial noise filter or a commercial noise cut

transformer.

 Use the attached power cord and insert it directory

with the ground terminal. Do not use power cords

intended for other products with this machine.

 Do not use an extension cord. When use is

unavoidable, use a cord rated higher than 15A.

 Use of an extended cord may cause AC voltage

decrease and interfere with normal operation.

 During printing, do not shut off the power supply

or pull out the power supply plug.

 When not in use for consecutive holidays or long-

term travel, pull out the power cord.

 Do not use the attached power cord for other

products.

WARNING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oki ES4161 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oki ES4161

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info