665624
18
Zoom out
Zoom in
Vorherige Seite
1/92
Nächste Seite
Chapter 1 PREPARATIONS
14
Saving power when not in use – power saving modes –
This equipment supports three power saving modes; the Automatic Power Save mode, Sleep mode and Super Sleep
mode. The table below shows the procedures to switch modes manually and the conditions under which the equipment
enters into or recovers from each mode.
Power saving
modes
Procedure to switch
modes
Conditions to enter into
the mode
Status of equipment
Conditions to recover
from the mode
Automatic
Power Save
mode
When a specied period of
time
*1
has passed since the
last use of the equipment.
“Saving power - press
START button. appears on
the touch panel.
When a button on the
control panel
*2
is pressed
or when print data or fax
data are received.
Sleep mode
When the [POWER SAVE]
button
*3
is pressed or
when a specied period of
time
*4
has passed since the
last use of the equipment.
When a particular option
*5
is installed or when a
particular protocol
*6
is
enabled.
The touch panel display
goes o and the [POWER
SAVE] button lights in
green.
Same as the Automatic
Power Save mode.
Super Sleep
mode
When the [POWER SAVE]
button
*3
is pressed or
when a specied period of
time
*4 *7
has passed since
the last use of the
equipment.
When a particular option
*5
is not installed and also
when a particular protocol
*6
is disabled.
Only the MAIN POWER
lamp (green) lights.
When the [POWER] button
is pressed, when print or
fax data are received
through a wired LAN or
when the time set for
Scheduled Print has come.
*1 The default value set at the factory shipment is 1 minute.
*2 Any of the [START], [POWER SAVE], [COPY], [Filing Box], [SCAN], [PRINT] and [FAX] buttons.
*3 [POWER SAVE] button on the control panel.
*4 The default value set at the factory shipment is 1 minute (The default value set at the factory shipment of the European version is 10 minutes).
*5 The Wireless LAN Module and/or OKI IC Card Reader.
*6 Any of IPX, AppleTalk and other protocols. When the IPsec function is enabled or the Ethernet speed is set to [AUTO (-1000MB)] or [1000BASE FULL], the
equipment enters into the Sleep mode. For details, refer to the following guide:
& TopAccess Guide (PDF): “Chapter 8: [Administration] Tab Page - “[Setup] Item list
*7 Depending on the network environment of the user, the time for switching to the Super Sleep mode may take more than 10 minutes even though it
has been set to 10 minutes or less.
For changing the set period of time for entering into each mode, refer to the following guide:
& MFP Management Guide (PDF): “Chapter 2: SETTING ITEMS (ADMIN)” - “Setting General Functions
When the set period of time for switching to the Automatic Power Save mode is the same as that for the Sleep mode or
the Super Sleep mode, the equipment enters into the Sleep mode or the Super Sleep mode after the set period of time.
For the European version
Contact your service representative to change the default settings noted above.
18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Oki ES9465 MFP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info