Bedienungsanleitung Oki MB290 (Seite 52 von 100) (Englisch)

492984

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

MB290

- 47 -

9 - Network features

Network features

You may connect your multifunction terminal to an

Ethernet or a wireless network.

However, practical knowledge of your computer

configuration is required to set up a network.

Selecting the type of your local

network

This parameter allows you to configure your terminal

accordingly to the type of network you will install it in.

 26 - SETUP / LOCAL NETWORK

1 Select the desired network type using the  or 

buttons

- WLAN if using a wireless network

- LAN ETHERNET if using a wired network

2 Confirm with OK.

Ethernet network settings

Automatic configuration

We recommend that you carry out a manual configuration

of your terminal. The automatic configuration of the local

network settings may be considered, if your local network

features a DHCP or BOOTP server that can dynamically

assign addresses to the peripheral devices present on the

LAN.

To automatically configure the local network settings:

 2711 - SETUP / LAN ETHER / PARAMETERS / IP

CONFIG.

1 Choose Automatic and press OK to confirm. The

terminal scans the local network for a DHCP or

BOOTP server that can assign it its settings

dynamically (the message S

ELF

CONF

displayed).

2 Once the message S

ELF

CONF

has disappeared,

check for the IP Address, Sub-network mask and

Gateway address. If these are missing, you should

carry out a manual configuration (see below).

Manual configuration

To configure your terminal manually, you should obtain

the usual information used to set a peripheral device (IP

address, sub-network mask, network and gateway

address).

To configure the local network setting manually:

 2711 - SETUP / LAN ETHER / PARAMETERS / IP

CONFIG.

1 Choose Manual and press OK to confirm.

IP address

 2712 - SETUP / LAN ETHER / PARAMETERS / IP

ADDRESS

1 Enter the IP address of your terminal and press OK

to confirm.

Sub-network mask

 2713 - SETUP / LAN ETHER / PARAMETERS /

SUBNET MASK

1 Enter the sub-network mask of your terminal and

press OK to confirm.

Gateway address

 2714 - SETUP / LAN ETHER / PARAMETERS /

GATEWAY

1 Enter the IP address of the network gateway and

press OK to confirm.

IEEE Address (or Ethernet address) or MAC

address

 2715 - SETUP / LAN ETHER / PARAMETERS / IEEE

ADDRESS

The Ethernet card of your terminal already has an

unmodifiable, yet consultable, IEEE address.

NetBIOS names

These names, which can be used with the network

options, are used to identify your terminal machine from a

PC connected to a local network (for instance with the

name "IMP-NETWORK-1").

 2716 - SETUP / LAN ETHER /PARAMETERS /

NETBIOS 1

 2717 - SETUP / LAN ETHER / PARAMETERS /

NETBIOS 2

1 Enter the selected name (15 characters max) and

press OK to confirm.

Name servers

The WINS1 and WINS2 servers, used with the network

options, allow access to terminals on other sub-networks

by means of their NetBIOS name.

Note

These two addresses must be filled in

for the Scan To Disk function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oki MB290 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oki MB290

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info