645020
34
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
HOW TO MAKE COPIES
- 34 -
1
2
3
4
5
6
Note
If you want to change settings such as the reproduction
ratio, density, original mode or 1/2-sided copying, you must
finish the proof copy first. Then change these settings and
scan the original again.
1
Place paper in the tray(s).
2
Place the original(s).
3
Select the number of copy sets and copy
modes.
4
Press [PROOF COPY] on the touch panel.
“PROOF COPY is set. Press START button to copy.”
appears for approx. 2 seconds.
Note
If [NON-SORT NON-STAPLE] or [GROUP] is selected
as a finishing mode, the mode will be changed to
[SORT] automatically.
5
Press the [START] button on the control
panel.
Scanning starts. 1 set of copies will be printed out.
6
Change the number of copy sets and copy
modes as required after checking the proof
copy.
Modes or settings such as the number of copy sets, the
receiving tray, page number, time stamp, and sort/stapling
can be changed.
Note
If you want to change settings such as the reproduction
ratio, density, original mode or 1/2-sided copying, you
must finish the proof copy first. Then change these
settings and scan the original again. Press [MEMORY
CLEAR] on the touch panel or the [RESET] button on
the control panel to end the proof copy.
7
Press the [START] button on the control
panel.
If you did not change the number of copies in step 6
above, the number of copies printed out will be one fewer
than that previously set because you have already copied
one as a proof copy. (However, if the number of copies
you previously set was 1, another set of copies will be
printed out besides the proof copy.)
Selecting face down/up stacker
You can select the face down/up stacker if the Inner finisher is
installed.
Note
The available face down/up stacker may be restricted
depending on copy modes and paper sizes.
Face down/up stacker selection is set at automatic selection
by default.
Changing the face down/up stacker
The face down/up stacker currently selected is displayed on
the equipment status indication area. To change the face down/
up stacker, press [OUTPUT BIN]. Every time you press this,
the display changes from the face down/up stacker of the
equipment, the face down/up stacker of the Inner Finisher, and
automatic selection in this order.
34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Oki MPS3537 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Oki MPS3537

Oki MPS3537 Bedienungsanleitung - Deutsch - 100 seiten

Oki MPS3537 Bedienungsanleitung - Deutsch - 363 seiten

Oki MPS3537 Bedienungsanleitung - Englisch - 357 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info