Bedienungsanleitung Oki MPS4200 (Seite 21 von 203) (Englisch)

645022

Zoom out

Zoom in

Vorherige Seite

1/203

Nächste Seite

Installing Your Machine

-21-

Setup

The <

POWER SAVE

> key lights up while in the mode.

Memo

 By factory default, the time interval to enter the power

saving mode is set to 1 minute. You can change the time

interval by pressing the <SETTING> key on the operator

panel and selecting [Admin Setup] > [Management] >

[Power Save] > [Power Save Time].

 Sleep Mode

Your machine goes from the power saving mode

into the sleep mode after a set period of time. In

the sleep mode, the status of your machine is

almost the same as when it is turned off.

The <POWER SAVE> key blinks while in the

sleep mode.

Note

 The machine does not enter the sleep mode if an error

occurs.

 If time-set transmission is scheduled, the machine will not

go into sleep mode.

 If the fax transmission is waiting for a redial, the machine

cannot enter sleep mode.

 When the network connection is switched from wired to

wireless, sleep mode is disabled. To enable sleep mode for

devices connected using wireless LAN, enable sleep mode

from the sleep mode setting menu. (MB451w and MB471w

only)

 When a device using the wireless LAN connection goes into

sleep mode, the wireless LAN connection is broken. To

reconnect to the wireless LAN, press the power save key

on the device to recover from sleep mode. (MB451w and

MB471w only)

 After the device connected to the wireless LAN has

recovered from sleep mode, it automatically connects to

the wireless access point using the same settings as before

it went into sleep mode. However, it may take up to 1

minute to connect. (MB451w and MB471w only)

 When the network connection is switched from wireless

LAN to wired LAN, sleep mode is enabled. (MB451w and

MB471w only)

Memo

 By factory default, the time interval to enter the sleep

mode is set to 30 minutes. You can change the time

interval by pressing the <SETTING> key on the operator

panel and then selecting [Admin Setup] >

[Management] > [Power Save] > [Sleep Time].

 Returning to the Standby Mode

To return the machine to the standby mode from

the power saving or sleep modes, press the

<POWER SAVE> key on the operator panel.

Memo

 When your machine receives a print job from a computer

or other devices, it automatically returns to the standby

mode.

Auto Power Off

When your machine is not used for a certain

period of time, the power turns off automatically.

Once the machine turns off, you need to turn on

to use it.

The machine has three settings to select the

machine's behavior on Auto Power Off.

Enable

Auto Config

Disable

Enable

When your machine is not used for a certain

period of time, it turns off the power

automatically.

Auto Config

The machine will not turn off automatically under

the conditions listed below.

- An Ethernet cable is attached to network

interface connection

- A telephone cable is attached to LINE

connection

Disable

The Auto Power Off function is disabled. The

machine will not turn off automatically.

Note

 In the following cases, the Auto Power Off function is also

disabled.

- When an error occurs

- When time-set transmission is scheduled

- When the fax transmission is waiting for a redial

-When [Auto Power Off] is [Auto Config.] and

Ethernet cable is attached

-When [Auto Power Off] is [Auto Config.] and

telephone cable is attached

Memo

 By factory default, the time interval to turn off the power

is set to 4 hours. You can change the time interval by

pressing the <SETTING> key on the operator panel and

then selecting [Admin Setup] > [Management] >

[Power Save] > [Auto Power Off Time].

 By factory default, [Auto Power Off] is set to [Auto

Config] or [Disable]. You can change the setting by

pressing the <SETTING> key on the operator panel and

then selecting [Admin Setup] > [User Install] >

[Power Save] > [Auto Power Off]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oki MPS4200 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oki MPS4200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info