Bedienungsanleitung Oleo-Mac GS200E (Seite 34 von 202) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

644159

Zoom out

Zoom in

Vorherige Seite

1/202

Nächste Seite

RUS

- Be extremely careful when working on

slopes or uneven surfaces.

- Stop the motor before setting the chain saw

down.

- Do not lean forward and do not cut above

shoulder height; gripping the saw at the top

of the handle makes it difficult to control and

counteract kickback (Fig. 20).

- Do not use in trees or on steps, this is

extremely dangerous (Fig. 20).

- Ensure that the cable does not snag on

parts of the tree when the machine is in

operation.

- Stop the saw if the chain strikes a foreign

object. Inspect the saw and repair or replace

parts as necessary.

- Keep the chain out of dirt and sand. Even a

small amount of dirt will quickly dull a chain

and increase the possibility of kickback.

- Always keep the handles dry and clean.

- When cutting a limb that is under tension, be

alert for springback so you will not be struck

when the tension in the wood fibre is

released.

- Take great care when cutting small branches

or shrubs which can block the chain, be

thrown back towards you or cause you to

lose your balance.

8. MAINTENANCE



WARNING - The motor is designed so

as not to become overheated during

normal use. A possible overheating can

be caused by worn or badly sharpened

chain, inadequate chain lubrication,

excessive pressure on the electric saw while

cutting, obstruction of the motor sir slits

or an inappropriate extension cord. During

maintenance operations, always wear

protective gloves and make sure that the

plug for mains connection is disconnected.

Inspect the tool before each use to check for

worn or damaged components. Do not use

the chain saw if you notice any broken or

excessively worn parts.

General cleaning

• Keep the tool clean. Remove all woodchips

after each use and before stowing the tool

away.

• Regular and correct cleaning will help to

keep the tool in safe working order and

extend its working life.

• Clean the tool with a dry cloth. Use a brush

to clean hard-to-reach areas of the tool.

• Take special care in cleaning the air intakes

with a brush after each use of the tool. Clear

away any hard to remove debris using

compressed air (max. 3 bar) (Fig.27).



CAUTION - Do not use aggressive or

alkaline chemicals, abrasives or other

detergents or disinfectants to clean the tool;

such products may damage the outer of the

tool.

CHECK/REPLACEMENT OF THE BRUSHES

Every 100 work hours the brushes should be

checked by your authorized servicing dealer.

Replacement is recommended aner 200

work hours. For check of brushes, please call

authorized dealers or workshops.

WARNING - Require the assembly of

original brushes. The brushes must be

replaced in pairs.

EXTRA MAINTANANCE ADVISABLE

It is advisable to inspect the machine by a

specialized technician at an authorized service

network at the end of season, if used

intensively, and every two years if with normal

use.



WARNING: All maintenance operations

not reported in this manual must be

carried out by an authorized Service Center.

To ensure steady and regular electric saw

operation, remember that parts must only be

replaced with ORIGINAL SPARES.



Any unauthorized changes and/or

use of non-original replacement parts

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oleo-Mac GS200E Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oleo-Mac GS200E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info