Bedienungsanleitung Olimpia Splendid Maestro Smart (Seite 21 von 40) (Englisch)

776121

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

MAESTRO SMART

US-ENG- 9

US-ENGLISH

2.4.3 - ASSEMBLY OF THE AIR DUCTS AND EXTERNAL GRILLES (g.10-11-12)

• Afterhavingdrilledtheholes,inserttheplasticsleeves(suppliedwiththeunit)intothem.Sincethe

sleeves are made for 8” (200 mm) holes, the installer will have to trim 5.1” (129 mm) from the long side

of the sleeve, if using 6.4” (160 mm) holes.

The length of the sleeves must be 2.5” (63.5 mm) less than the thickness of the wall. Roll up the sleeves

and insert them into the hole. Pay attention to the splicing line (G) which must always face upwards.

To position the external grids, proceed as follows:

a. Applytheseal(D)tothewallange(F),ensuringitlinesupwiththeouteredgeoftheangeasindicated

inthegure13.

b. Fixthetwoangesusing2pegswithadiameterof1/4”(6mm)andcheckthatthetwoxingholesare

horizontal.

c. Fitthesmalleyeletofthespring,withthelongstem,onthecappin,onbothcomponents.(g.17)

d. Insert the two caps (with spring), on the front part of the external grille, on its two housings, pulling until

itclicks(g.18)thencouplethetwochainstothelargeeyeletofthespring.

e. Using one hand, grip the two chains connected to the grille.

f. Bendtheexternalgrilleback,grippingthemwithyourfreehandwheretheybendandinsertyourngers

insidethesinglelouvres(g.19).

g. Insert your arm into the sleeve until the grille protrudes completely outwards. reopen the grille, being

carefultokeepyourngersinsidethelouvres.

h. Turn the grille until the louvres are fully horizontal and tilted downwards.

i. Pullthechain,tensioningthespring,couplethechainringtothepinoftheinnerangethroughwhich

thesleevespass(g.20).

l. Use hand shears to cut off any excess chain links.

Olimpia Splendid recommends using the supplied grilles, or grilles with similar char-

acteristics that are factory approved to ensure proper unit performance.

2.4.4 - PREPARING THE HOLES ON THE UNIT

The unit is designed to operate with 6.4” (165 mm) sleeves, however to ensure the best performance and

lowest air noise level, the factory recommendation is to use the 8” (200 mm) holes. if using the 8” (200 mm)

sleevesuseacuttertoremovetheknockoutfromtherearoftheunit(g.21).

2.4.5 - FITTING THE UNIT ON THE BRACKET (g.22-23-24-25)

After ensuring the mounting bracket is properly anchored to the wall and that all required preparatory work

hasbeencarriedoutfortheelectricalconnectionsand/orthecondensatedrainagetheunitcanbexedto

the wall. Lift the unit by holding it from the sides of the lower base.

To facilitate the operation of fastening it to the bracket, tilt it slightly toward you. To make the electrical con-

nection and fasten the drain pipe, place a wedge between the unit and the wall.

 Whenyouhavenished,inspectcarefullytomakesuretherearenoopenspacesattherearoftheunit.

 Theinsulatinggasketmusttrmlyagainstthewall,particularlyintheareawhereairentersandleavesthe

unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olimpia Splendid Maestro Smart Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info