Bedienungsanleitung Olimpia Splendid MIA 2 9 (Seite 15 von 60) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

703016

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

is easily opened and inspected through the air-tight door.

• Whenever ﬂues with parallel exits are used it is advisable to raise the upwind chamber

by one element.

• The chimney tube must never pass across a combustible surface.

The Chimney Cap

The chimney cap must respect the following requirements:

• It must have the equivalent diameter and internal form of the ﬂue.

• It must have a useful outlet diameter of not less than double that of the ﬂue.

• The chimney cap on the roof or that remains in contact with the outside (for example,

in case of open lofts or attics), must be covered with elements in brick or tile and

must, in any case, be well insulated.

• It must be constructed to prevent rain, snow, and extraneous bodies from entering the

ﬂue and so that the discharge of the products of combustion is not inhibited by wind

from any quarter or strength (windproof chimney cap).

• The chimney cap must be positioned in such a way as to guarantee the adequate di-

spersion and dilution of the products of combustion and in any case, must be out of

the reﬂux zone. This zone has different dimensions and forms according to the angle

of inclination of the roof so it is necessary to adopt minimum heights (Fig. 2).

• The chimney cap must be a wind-proof type and must be above the ridge.

• Eventual structures or other obstacles that are higher than the chimney cap must not

be too close to the chimney cap itself.

Canalisation (if available)

Before you connect the auxiliary pipes for the canalisation of the air, please check that:

• The canalisation system is according to law.

• The system does not present any obstructions.

• Once you connect the stove and use the air ducting, there is a regular air ﬂow at the

end of the canalisation.

• You can use up to two hot air delivery pipes with a maximum lenght of 4 m. each. If

you use only one pipe, the maximum lenght is 5 m. For more information see chapter

6.0.

• The piping and conduit must be protected with ﬁxed, non-reclosable grids or suitable

covers. The minimal section must not be reduced anyway.

Sizing

Smoke discharge

The discharge system must be for the stove only (it is not permissible to discharge into

ﬂues in common with other devices). The smoke discharge takes place through the 8

cm diameter tube placed at the back. A “T” with a condensation collection cap should

be provided. The smoke discharge of the stove must be connected with the outside

using a steel or black tube (resistant up to 450°C) without obstructions.

The tube must be hermetically sealed. To make the tubes airtight and for their eventual

insulation, it is necessary to use material resistant up to at least 300°C (silicone or putty

for high temperatures). The horizontal sections can be up to 2 m long. It is possible to

have up to three 90° curves.

If the smoke duct is outside it must be insulated (Fig.4).

If the smoke duct is inserted in a ﬂue (Fig.3), this must be certiﬁed for solid combustibles

and if it is larger than 150 mm in diameter, modiﬁcation is necessary by inserting a tube

and sealing the discharge with respect to the parts in brickwork.

It must be possible to inspect all the sections of the smoke duct. If it is a ﬁxed duct it

must have openings for inspection and cleaning.

The adjacent locale must not be used as a garage or be a space without ventilation

or air exchange, a storage area for combustible material or used for an activity

that has a ﬁre hazard. According to the norm UNI 10683/98, the stove must not be in

the same environment where extractors, type B gas devices or in any case, devices that

create lower atmospheric pressure in the locale are found.

External air intake

The stove must be furnished with the air necessary to guarantee the regular functioning

of the combustion and an environmental well being.

• Be sure that the room where the stove is installed has sufﬁcient aeration and, if ne-

cessary, install an air intake duct with a minimum recommended diameter of 50 mm

and max length 1,5 m to bring in air from the outside.

• The external air intake must communicate with the stove and positioned so that it is

not obstructed. It must be protected with a permanent non-closable grill or other sui-

table protection provided that the minimum diameter is not reduced.

• The air ﬂow can also be acquired from a locale adjacent to where the stove is installed

as long as that ﬂow can freely cross the permanent non-closable openings that com-

municate with the outside.

• The presence in the local adjacent to where the stove is installed, of other devices in

use or of suction devices that cause a contrary draught effect must not create a lower

air pressure in the locale than in the outside environment.

• In the adjacent locale the permanent openings must respond to the requisites which

are listed in the points above.

Positioning

The stove is furnished with an electrical cable to connect to a 230V 50Hz socket, pre-

ferably with a thermal-magnetic switch. Variations in tension of more than 10% can

compromise the stove (if not already present, an adequate differential switch should be

provided). The electrical system must comply with the norms; verify in particular the ef-

ﬁciency of the ground circuit. The electrical feed cable must be of a diameter adequate

to the power of the device. The stove must be completely level. Verify the weight bearing

capacity of the ﬂooring.

The placement of the stove within the living environment is determined so that the en-

vironment is heated in a uniform manner.

Before deciding where to place the stove, keep in mind that:

• The air used for combustion must not come from a garage or a space without venti-

lation or air exchange, but from a free space or the outside;

• The stove should not be installed in a bedroom;

• Rather it is preferable to install the stove in a large, central room of the house to insure

the maximum heat circulation;sicurare la massima circolazione del calore;

Fig.2: characteristics of the chimney cap

NOSI

Fig.3: internal ﬂue installation to do according to norms

Air intake

min. 1,5 m

Condensation collection cap

Air intake

Condensation collection cap

Presa d’aria

Insulated tubing

Olimpia Splendid MIA 2 9 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info