Bedienungsanleitung Olimpia Splendid NEXYA S4 E - PENTA INVERTER 42 (Seite 76 von 336) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

688894

Zoom out

Zoom in

Vorherige Seite

1/336

Nächste Seite

ø 6,35 mm

1500

(153 kgf/cm)

1600

(163 kgf/cm)

ø 9,52 mm

2500

(255 kgf/cm)

2600

(265 kgf/cm)

ø 12,7 mm

3500

(357 kgf/cm)

3600

(367 kgf/cm)

ø 16 mm

4500

(459 kgf/cm)

4700

(479 kgf/cm)

ENGLISH

EN - 22

Lunghezza tubo di

connessione

Quantità aggiuntiva di

refrigerante da caricare

Inferiore a (5 x N) m ----------

Superiore a (5 x N) m

R410A: (lunghezza totale

del tubo - 5 x N) x 15 g/m,

N=2,3,4 or 5

N = n° unità interne installate

NEVER USE A NORMAL HANDSAW,

scraps could fall inside the pipe and enter the circuitry of the system, damaging



c. Remove possible burrs with the special tool.

mmediately after cutting and deburring the pipes, seal the ends with insulating

tape.

d. If you do not use preinsulated pipes, they must be insulated as follows:

 

 

) or 0.39 kcal/(h x C x m

)

 

 

Do not place both pipes in the same sheath, as this would jeopardize the proper



e. Bind any joints in the sheath securely with insulating tape.

f 

g

h. Lubricate the connecting thread with oil for coolant.

DO NOT USE ANY OTHER TYPE OF LUBRICANT

i. Screw the pipe nut manually on

the connecting thread.

l 

a wrench to hold the threaded

part of the attachment still (to

prevent deformations), and a

dynamometeric wrench on the



Calibrate the dynamometric

wrench to the value suitable for

the pipe dimensions.

2.6.4 - Tests and inspection

After making all pipe connections, check the seal of the system.

Operate as follows:

a 

b. Connect a tank of anhydrous nitrogen to the coupling with a 5/16” connector and a pressure reducer.

c. Open the tap on the tank and pressure reducer and bring the pressure in the circuit to 3 bar; close the

tank.

d. If after about 3 minutes the pressure does not drop, the circuit is in good working order and the pressure

can be raised to 15 bar by reopening the tank.

e. Check again after 3 minutes that the pressure remains stable at 15 bar.

f. For safety reasons apply a solution of soapy water to the connectors and check for the formation of bub-

bles revealing leakage of gas.

g. If the pressure should drop and the search on the attachments with soapy solution gives a negative

outcome, introduce R32 gas into the circuit and look for the leak using a leak detector.

Since the circuit has no welding points, the leaks should only be present in the piping joints. In this case,

External diameter

of the pipe



(N.cm)

Additional coupling



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olimpia Splendid NEXYA S4 E - PENTA INVERTER 42 Seite 76

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info