Bedienungsanleitung Olivetti LAB_100 (Seite 45 von 64) (Englisch)

16535

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

4. Press the key

until the display shows:

RING VOLUME:HIGH

5. To view the other available options, "RING VOLUME:LOW",

"RING VOLUME: MED" and "RING VOLUME:OFF", press

the keys:

6. To confirm your choice, press the key:

7. To return the fax machine to its initial stand-by mode, press

the key:

TO ENABLE/DISABLE RECOGNITION OF THE RING

FREQUENCY

In some countries, local telephone companies offer the pos-

sibility of assigning the same telephone line two or

more numbers, corresponding to different users. When

an incoming call is received, a different ring frequency

will indicate which user is to answer the call.

This function is extremely useful at home or in small offices,

where the same telephone line is shared by more than one

person.

Your fax machine is capable of "learning" one of

these frequencies (see the procedure that follows). In

this way, when a call with the specific ring frequency is

received, the fax machine (in "PHONE/FAX" and "TAD/

FAX" reception modes) prepares exclusively to receive a

document.

This function is particularly useful when associated

with silent reception in that the fax machine will only ring

if the call is coming from a telephone.

1. Press the key

until the display shows:

INSTALLATION

2. Press the key:

The display shows:

TEL. LINE SET-UP

3. Press the key:

The display shows:

ENHANCED FEATUR.

4. Press the key

until the display shows:

DISTINC.RING:OFF

5. Press the keys

/ until the display shows:

CHANGE PATTERN

6. To confirm your choice, press the key:

The display shows:

AUTODETECT. RING

7. Call the fax machine with the desired frequency so that the

fax machine detects it.

The display shows:

RING DETECTED

8. To return the fax machine to its initial stand-by mode, press

the key:

notE

If the fax machine cannot detect that particular frequency, the display

will show the message "RING NOT DETECT.". At this point, press

the

key and repeat the procedure.

TO CHANGE THE LENGTH OF THE ACOUSTIC SIGNAL

This function is only enabled in some countries.

When the fax machine is set up for automatic reception

with recognition of the type of call, it behaves as

follows:

• if it is being called by a fax machine, it will automatically

prepare to receive a document after the preset number of

rings

• if it is being called by a telephone, it will emit an acoustic

signal for a time of 20 seconds, after which, if you still have

not lifted the handset, it will automatically prepare to re-

ceive a document.

If you want, you can change the length of the acoustic signal

as follows:

1. Press the key

until the display shows:

INSTALLATION

2. Press the key

until the display shows:

FAX/TEL TIMER:20

3. To view the other available values, "15", "30" or "40",

press the keys:

4. To confirm your choice, press the key:

5. To return the fax machine to its initial stand-by mode, press

the key:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olivetti LAB_100 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Olivetti LAB_100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info