Bedienungsanleitung Olsberg Aracar Compact (Seite 28 von 72) (Deutsch, Englisch, Holländisch, Französisch)

707627

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Installation of the stove

The oor on which the stove is installed must be even and

horizontal. The stove may only be installed on an adequate

load-bearing oor.

If the ooring is inammable, a stable and non-combusti-

ble spark protection plate must be used. This must extend

50 cm to the front and 30 cm to each side beyond the edge

of the combustion chamber opening.

Assembly sequence

Notice: The description below sets out the installation se-

quence for the Aracar stove with door stop left (see Fig.1).

The installation sequence is mirrored for the door stop on

the right (see Fig.2).

● If specied, install the electric stove controller OEC.

● Determine the installation location. The stove can be

installed ush with the wall on 2 sides. There must be

no objects made of combustible materials within a dis-

tance of 80 cm of the stove’s radiation area, measured

from the combustion chamber’s inspection glass, nor

may any be placed within this area subsequently see

Fig.3).

● Position the bottom plate (9,Fig.4) at the installation lo-

cation in such a way that the two 80mm thick insulation

panels 1+2 face the mounting walls (see Fig.3).

● Install the pipe lining (customer-provided) in the

chimney. If you use the Olsberg elbow pipe (part

no. 23/1974.9392), the connection height measured

up to the middle of the stove pipe is 1,520mm. If the

stove pipe is supposed to be connected inside the clad-

ding, the dimension of 1,520mm can be extended to-

wards the top by up to 100mm. If the stove pipe is sup-

posed to be connected on the outside of the cladding,

it must rst be routed straight through the cover by at

least 500mm and connected with a suitable elbow pipe.

● Depending on the position of the chimney, you may

have to balance out the angular oset using a rotating

elbow. There should be no ammable material with-

in a 20cm circle around the stove pipe, for the passage

through structural components made of ammable

materials.

● Copy the 160mm diameter hole for the stove pipe con-

nection to insulation board 1 or 2 and make a corre-

sponding cut-out using a long jigsaw blade.

● Place the stove on the bottom plate and into the holes

designated for the adjustable feet.

● Align the stove such that the distance between the

bottom plate and the bottom edge of the combustion

chamber door is 450mm all around (see Fig.4).

● Set up insulation boards 1+2 and, if necessary, x

them in place on the mounting walls using a few ad-

hesive joints. When installing the stove on 1 side with

the mounting wall behind insulation board Pos.2, you

can also screw the two insulation boards together us-

ing 3 chipboard screws Ø6x140 (17) (no pre-drilling and

countersinking necessary). In any case, both boards

must be glued together one below the other.

800

2 1

Fig.3

450

Fig.4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olsberg Aracar Compact Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info