Bedienungsanleitung Olsberg ARINA 2.0 (Seite 70 von 160) (Deutsch, Englisch, Französisch)

812264

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Installation instructions

for the specialist company

LEVANA 2.0 6 kW

LEVANA 2.0 8 kW

LEVANA AQUA 2.0

ARINA 2.0

INARA 2.0

2.8 LEVANA AQUA 2.0 water installation

Water side connection

The water pipes can optionally be laid to the rear (installed in the

factory) or to the bottom through the oor.

For laying through the oor, you must remove the lower rear wall

and adjust the mounting for the ow and return ow accord-

ingly. For laying of the water pipes through the oor, as well as for

removal / installation of the rear cladding, follow a similar procedure

to that which is set out in the “Combustion air nozzles for connec-

tion from the bottom” chapter.

5431 2

Fig. 2.36 Water side connections on the rear of the pellet replace

1Socket for connection of the 3-pole connector for the pump

2Socket (pastel blue) for the top buer sensor connection

3Socket (light blue) for the bottom buer sensor connection

4½” heating return

5½” heating ow

Important information for integration of the pellet re-

place into the heating system and/or domestic cooling

water system:

ū The water connections and the electrical work may only be car-

ried out by expert technicians.

ū We recommend the “Olsberg installation unit” (item no.:

23/5591.9250) for integration into the heating system and/or do-

mestic cooling water system. Observe the separate manual for

this unit here.

ū In addition to the necessary safety components, a return ow in-

crease valve which increases the return ow temperature to at

least 55 °C must always be installed (integrated into the “Olsberg

installation unit”).

ū An outlet tap must be installed in the bottom section of the wa-

ter circuit.

ū A buer must be integrated into the heating system for ecient

and fault-free operation of the LEVANA AQUA 2.0 pellet replace.

As a guideline for the storage volume, approx. 60 litres should be

provided per kW of heating output (approx. 500 litres).

ū For ecient operation of the pellet replace, it is strongly rec-

ommended that both buer sensors (top and bottom) be

connected!

●Clean the heating system before hydraulic connection of the pel-

let replace through ushing in accordance with DIN EN 14336

(Heating systems in buildings – Installation and commissioning

of water based heating systems) so that the function of the pellet

replace is not endangered!

Proof of cleaning must be provided in the event of possible war-

ranty services from Olsberg.

●The pellet replace may never be operated without water.

●The locally applicable regulations and technical rules must also al-

ways be observed!

Venting at the vent valve

●After connection of the ow and return line and lling with wa-

ter, the system should be vented at the vent valve for the pellet

replace.

●Check all water connections on the pellet replace for leaks!

Fig. 2.37 Venting

1Vent valve

We reserve the right to make technical changes

78-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 7078-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 70 11.04.2023 14:41:5111.04.2023 14:41:51

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olsberg ARINA 2.0 Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info