Bedienungsanleitung Olsberg Auriga (Seite 9 von 32) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

812270

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Combustion air supply

It must be guaranteed that there is enough combustion

air available for the stove. For the proper function of the

stove, a necessary combustion air volume current of

15,6 m³/h must be considered.

External combustion air connection

By an external operating mode, the combustion air

can be added from outside through a leak-proof line or

through a supply duct in the chimney. Thus, speak with

your district chimney sweep master.

Due to energy saving reasons, the combustion air in-

let should be able to be blocked if the stove is not being

operated. This can occur through a shut-off valve in the

combustion air line or through the air slide valves on

the stove. If a shut-off valve is used, this must be clear-

ly identied with CLOSED/OPEN.

Through the shutoff, it is avoided that heat is removed

from the set-up room through the constant circulation

of cold combustion air and cold combustion air lines

may lead to an increased formation of condensation.

Attention:

The combustion air line may not be closed during

operation!

In order to feed the combustion air to the stove exter-

nally via a pipe instead of from the room in which it is

installed, it is possible to screw a Ø 125 mm combus-

tion air pipe to the back of the stove. If the combus-

tion air pipe installed is longer than 3 m, calculations

will have to be carried out to verify an adequate sup-

ply of combustion air. At extremely low outdoor temper-

atures, condensation can occur on the combustion air

duct. For this reason it must be insulated with a suitable

insulating material. Observe the rules of the oven and

air heating construction craft.

Use the Olsberg combustion air pipes with sealing lip.

Attention:

Appliances with external combustion air connec-

tion are not suitable for concurrent operation with

ventilation systems, without a supplemental safe-

ty system.

Installing the stove

The oor on which the stove is installed must be even

and horizontal. The stove may only be installed on an

adequate loadbearing oor. The stove can be stood

on a metal oor sheet or glass sheet to protect the

ooring.

If the ooring or carpet is inammable, a stable and

non-combustible spark protection plate must be used.

This must extend 50 cm to the front and 30 cm to each

side beyond the edge of the combustion chamber

opening. Under the stove no spark protection plate is

required.

Assembly sequence

●The Ø 150 stovepipe connection can be installed at

the top or rear. The stove is supplied ready for con-

nection from above. If you wish to connect it at the

rear, the following steps must be carried out to make

the necessary modications:

- Break out the cover in the back panel.

- Replace the connector sleeve and the sealing

cover.

●Decide where the stove is to be installed. There

must be no objects made of combustible materials

within a distance of 90 cm of the stove’s radiation

area, measured from the combustion chamber’s in-

spection glass, nor may any be placed within this

area subsequently.

Minimum distance from combustible or load-

bearing walls: lateral 20 cm and rear 10 cm

●Install the pipe lining (provided on site) in the chim-

ney. The connection height can be individually spec-

ied for a top stovepipe connection, however should

not exceed 1.5 m from the connector sleeve. For the

rear stovepipe connection heights please refer the

“Technical Data“ chapter. No combustible material is

permitted within a radius of 20 cm around the stove

pipe.

●Connect the stovepipe at both connection points

with stove putty so that the stove pipe is permanent-

ly sealed.

●Push the stove onto its planned position and orient it

so that the stovepipe ts into the pipe lining.

The stovepipe connections must be tight. The

stovepipe must not protrude into the chimney.

Bear in mind that on partition walls in accordance

with test specication EN 13240 the temperature

of 85°C can be reached, and with light wallpaper

or similar combustible construction materials this

can result in colour changes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olsberg Auriga Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info