Bedienungsanleitung Olsberg LEVANA 2.0 (Seite 73 von 160) (Deutsch, Englisch, Französisch)

812263

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Installation instructions

for the specialist company

LEVANA 2.0 6 kW

LEVANA 2.0 8 kW

LEVANA AQUA 2.0

ARINA 2.0

INARA 2.0

2.10 Checking the installation and function

●Check the fully completed installation (visual inspection)!

●Switch the pellet replace on and check all of the functions, and

check the chimney ue for leaks! Carry out initial commissioning!

2.11 Initial commissioning by the specialist company

●Please ensure that no objects made from ammable materials

are located or placed in the radiation range of the replace (min-

imum distance 800 mm, measured from the viewing window in

the combustion chamber door)!

●Before heating for the rst time, check that all accessories have

been removed from the ash pan and combustion chamber! To do

this, release the ash pan lock, which is located behind the inspec-

tion door, and pull the ash pan out to the front! The combustion

chamber door lock is located underneath the combustion cham-

ber door.

●Remove the protective lm from the touch control panel!

●Convection air openings may not be covered!

●The precautions for the combustion air supply may not be mod-

ied. In particular, care must be taken to ensure that the nec-

essary combustion air lines are open during operation of the

replace!

●Plug the white and blue connector supplied into the socket on

the rear of the appliance. If the pellet replace should be operated

with accessories (e.g. room thermostat)! Connect the connection

cables to the connector rst!

Note: the connector must be plugged in even without acces-

sories, otherwise the pellet replace is not ready for operation.

●Plug the shockproof plug into a 230 V/50 Hz shockproof socket.

●Fill the pellet reservoir with pellets (see chap. 3.2)!

●During initial commissioning, or if the pellet duct is empty, or

if the reservoir runs empty, a handful of pellets must be poured

into the burner trough towards the igniter. Otherwise, only the

pellet duct will be lled within the lling period in the start phase

and only an insucient 2-5 pellets will fall into the burner trough.

Fig. 2.41 Pour pellets in manually if the pellet duct is empty

●

Set the master switch to “I” (back right of the appliance)!

ū The touch control panel display is activated automatically.

Note: the smell which may occur as a result of curing of the

protective coating will disappear once the pellet replace has

been burning with good room ventilation for several hours.

Attention! Property damage! The pellet fireplace is coated

with a high-quality temperature-resistant coating which only

reaches its final strength after being heated for the first time.

You therefore should not place anything on the tiled pellet

fireplace or touch the surfaces as this may damage the

coating.

2.12 Handover of the system to the user

●After installation, instruct the user of the system with regard to:

ū Use,

ū Operation,

ū Functioning,

ū Care and cleaning (user),

ū Necessary annual maintenance (specialist company)!

●In particular, instruct the user of the system in the risks associated

with the pellet replace, as well as in the safety information and

safety precautions!

●Fill out the handover certicate (blank form attached)!

●Hand the product/the system over to the user together with this

manual and all other documents!

Commissioning certicate

The proper installation, commissioning and handover of the pellet

replace is documented by the commissioning certicate (sepa-

rate document). Instruction of the system user by the specialist

company, in particular in the risks associated with the pellet re-

place and in the safety information and safety precautions is also

certied by the specialist company and user’s signatures.

2.13 Disassembly and disposal

The applicable international, national and region-specic laws and

regulations at the time of disposal of the pellet replace must be

observed.

●Take care to ensure that the recyclability of materials, and the pos-

sibility of disassembly and separation of materials and assem-

blies is taken into consideration as well as the environmental and

health risks of recycling and disposal. Material groups such as

plastics and metals of dierent types should be sorted before be-

ing sent for recycling or disposal!

●The disposal and recycling of electrical and electronic compo-

nents must be done in accordance with the appropriate laws and

country-specic regulations!

We reserve the right to make technical changes

78-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 7378-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 73 11.04.2023 14:41:5211.04.2023 14:41:52

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olsberg LEVANA 2.0 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info