Bedienungsanleitung Olsberg Osorno (Seite 14 von 32) (Deutsch, Englisch, Holländisch, Französisch)

744280

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Operation

Permissible fuels

The following fuels are approved:

● Natural shopped wood in the form of billet wood

Maximum length: .....................33 cm

Circumference: .......... approx. 30 cm

Billet wood reaches a moisture content of 10 to 15% after

being stored outdoors for 2 to 3 years (only covered at the

top) and is then ideally suited for heating.

Freshly cut wood has a very high moisture content and

so burns badly. Apart from the very low caloric value it is

also harmful for the environment. The increased conden-

sate and tar formation can lead to replace and chimney

sooting.

This diagram shows that the consumption rate with fresh-

ly-felled wood (caloric value 2.3 kWh/kg) is almost twice

as high as the consumption rate with dry wood (caloric

value 4.3 kWh/kg).

Moisture [%]

dry wood that has been stored for at least 2 years

Caloric value [kWh/kg]

freshly-felled wood

You will only achieve optimum combustion and heat in

an environmentally friendly way with these fuels. Adding

the fuel in small quantities avoids unnecessary emissions.

Clean burning can be identied by the fact that the re-

brick becomes a light colour.

According to the German Federal Immission Control Act,

it is forbidden e.g. to burn the following fuels in stoves:

● Moist wood or wood treated with wood

preservatives

● Sawdust, chippings, grinding dust

● Bark and chipboard waste

● Slack coal

● Other wastes

● Paper and cardboard (except for igniting)

● Straw

Please note before heating for the rst time

● Remove all accessories from the combustion chamber.

● The odour given o by the evaporation of the protec-

tive coating disappears after the stove has been burn-

ing for several hours (ventilate the room well).

● The stove has a high quality temperature resistant coat,

which does not achieve its nal strength until the stove

has been heated for the rst time. You should therefore

never leave anything on the stove and not touch the

surfaces as the paint coat could otherwise be damaged.

● As soon as the kindling material has burned down, put

on 2 burnouts consisting of 3 kg wood ensuring that the

temperature resistant coating reaches its nal rmness.

Igniting

● Before ignition, check that no ammable objects are

placed on the stove.

● Empty the ash pan if necessary.

● Open the combustion air slide valve complete.

● Stack small amounts of rewood and, on top of it, kin-

dling material (igniter cubes and dry, smaller kindling)

and set the material alight.

● Close the door to the combustion chamber so that the

kindling material can catch re.

● Once there is a basic rebed, add more fuel according to

the heat requirement (see chapter “Heating”).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olsberg Osorno Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info