Bedienungsanleitung Olsberg Pacaya Compact (Seite 17 von 52) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

707632

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Installing the stove

The oor on which the stove is installed must be even and

horizontal. The stove may only be installed on an adequate

load-bearing oor. The stove can be stood on a metal oor

sheet or glass sheet to protect the ooring.

If the ooring or carpet is inammable, a stable and non-

combustible spark protection plate must be used. This

must extend 50 cm to the front and 30 cm to each side

beyond the edge of the combustion chamber opening.

Under the stove no spark protection plate is required.

Assembly sequence

● If intended, install the OEC.

● Install the side cladding.

● The Ø 150 stovepipe connection can be installed at the

top or rear. The stove is supplied ready for connection

from above. If you wish to connect it at the rear, the fol-

lowing steps must be carried out to make the necessary

modications:

- Break out the cover in the back panel.

- Replace the connector sleeve and the sealing cover.

● Install storage stones.

Comply with the information in the instruction manual

included with the storage stones.

● Decide where the stove is to be installed. There must be

no objects made of combustible materials within a dis-

tance of 80 cm of the stove’s radiation area, measured

from the combustion chamber’s inspection glass, nor

may any be placed within this area subsequently.

Depending on the installation position of the stove in

front of walls that need to be protected (ammable or

load-bearing), the following distances from walls need

to be observed in accordance with the position of the

combustion chamber door to the wall / side panel or

the back panel (see schematic diagram).

When not dealing with walls that need to be protect-

ed, you merely need to observe a minimum distance of

approx. 5 cm to allow for proper heat dissipation.

● Install the pipe lining (provided on site) in the chimney.

The connection height can be individually specied for

a top stovepipe connection, however should not exceed

1.5 m from the connector sleeve. For the rear stovepipe

connection heights please refer the “Technical Data“

chapter. No combustible material is permitted within a

radius of 20 cm around the stove pipe.

● Connect the stovepipe at both connection points with

stove putty so that the stove pipe is permanently sealed.

● Push the stove onto its planned position and orient it so

that the stovepipe ts into the pipe lining.

The stovepipe connections must be tight. The stove-

pipe must not protrude into the chimney.

Bear in mind that on partition walls in accordance with

test specication EN 13240 the temperature of 85°C

can be reached, and with light wallpaper or similar

combustible construction materials this can result in

colour changes.

20 cm

30 cm

80 cm

Stove installed straight in corner

20 cm

80 cm

Stove installed diagonally in corner

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olsberg Pacaya Compact Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info