Bedienungsanleitung Olsberg Palena Plus SD Compact (Seite 15 von 36) (Deutsch, Englisch, Holländisch, Französisch)

744282

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

15

Installing the stove

The floor on which the stove is installed must be

even and horizontal. The stove may only be in-

stalled on an adequate load-bearing floor. The

stove can be stood on a metal floor sheet or glass

sheet to protect the flooring.

If the flooring or carpet is inflammable, a stable

and non-combustible spark protection plate must

be used. This must extend 50 cm to the front and

30 cm to each side beyond the edge of the com-

bustion chamber opening. Under the stove no

spark protection plate is required.

Asembly sequence

●

If intended, install the OEC.

●

The Ø150mm stovepipe connection can be in-

stalled at the top or rear. The stove is supplied

ready for connec- tion from above. If you wish to

connect it at the rear, the following steps must be

carried out to make the necessary modifications:

‐

Break out the cover in the back panel.

‐

Replace the connector sleeve and the sealing

cover.

●

Decide where the stove is to be installed. There

must be no objects made of combustible materials

within a dis- tance of 80 cm of the stove‟s radiation

area, measured from the combustion chamber‟s in-

spection glass, nor may any be placed within this

area subsequently.

Depending on the installation position of the

stove in front of walls that need to be protected

(flammable or load-bearing), the following dis-

tances from walls need to be observed in ac-

cordance with the position of the combustion

chamber door to the wall / side panel or the back

panel (see schematic diagram).

When not dealing with walls that need to be protect-

ed, you merely need to observe a minimum dis-

tance of approx. 5 cm to allow for proper heat dissi-

pation.

If the stove is set up with the turntable, then the

turnta- ble must be positioned in such a manner

that the radi- ation area of the glass pane cannot

be turned in the di- rection of components that

must be protected, or the distance must be at

least 80 cm.

●

Install the pipe lining (provided on site) in the

chimney. The connection height can be individu-

ally specified for a top stovepipe connection, how-

ever should not exceed

1.5 m from the connector sleeve. For the rear

stovepipe connection heights please refer the

“Technical Data“ chapter. No combustible material

is permitted within a radius of 20 cm around the

stove pipe.

●

Connect the stovepipe at both connection points

with stove putty so that the stove pipe is perma-

nently sealed.

●

Push the stove onto its planned position and orient

it so that the stovepipe fits into the pipe lining.

The stovepipe connections must be tight. The

stove- pipe must not protrude into the chim-

ney.

Stove installed straight in corner

Stove installed diagonally in corner

Bear in mind that on partition walls in accordance

with test specification EN 13240 the temperature

of 85°C can be reached, and with light wallpaper

or similar combustible construction materials

this can result in colour changes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olsberg Palena Plus SD Compact Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info