Bedienungsanleitung Olsberg Salado Compact (Seite 14 von 28) (Deutsch, Englisch, Französisch)

744284

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Installing the stove

The ﬂoor on which the stove is installed must be even and

horizontal. The stove may only be installed on an adequate

load-bearing ﬂoor. The stove can be stood on a metal ﬂoor

sheet or glass sheet to protect the ﬂooring.

If the ﬂooring or carpet is inﬂammable, a stable and non-

combustible spark protection plate must be used. This

must extend 50 cm to the front and 30 cm to each side

beyond the edge of the combustion chamber opening.

Under the stove no spark protection plate is required.

Assembly sequence

● If intended, install the OEC or OEC SMART1.

● Install the side cladding.

● The Ø150mm stovepipe connection can be installed at

the top or rear. The stove is supplied ready for connec-

tion from above. If you wish to connect it at the rear, the

following steps must be carried out to make the neces-

sary modiﬁcations:

- Break out the cover in the back panel.

- Replace the connector sleeve and the sealing cover.

● Decide where the stove is to be installed. There must be

no objects made of combustible materials within a dis-

tance of 80 cm of the stove’s radiation area, measured

from the combustion chamber’s inspection glass, nor

may any be placed within this area subsequently.

Depending on the installation position of the stove in

front of walls that need to be protected (ﬂammable or

load-bearing), the following distances from walls need

to be observed in accordance with the position of the

combustion chamber door to the wall / side panel or

the back panel (see schematic diagram).

When not dealing with walls that need to be protect-

ed, you merely need to observe a minimum distance of

approx. 5 cm to allow for proper heat dissipation.

● Install the pipe lining (provided on site) in the chimney.

The connection height can be individually speciﬁed for

a top stovepipe connection, however should not exceed

1.5 m from the connector sleeve. For the rear stovepipe

connection heights please refer the “Technical Data“

chapter. No combustible material is permitted within a

radius of 20 cm around the stove pipe.

● Connect the stovepipe at both connection points with

stove putty so that the stove pipe is permanently sealed.

● Push the stove onto its planned position and orient it so

that the stovepipe ﬁts into the pipe lining.

The stovepipe connections must be tight. The stove-

pipe must not protrude into the chimney.

Bear in mind that on partition walls in accordance with

test specication EN 13240 the temperature of 85°C

can be reached, and with light wallpaper or similar

combustible construction materials this can result in

colour changes.

Dimensions in cm

Stove installed straight in the corner

Stove installed diagonally in corner

Dimensions in cm

110

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olsberg Salado Compact Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info