Bedienungsanleitung Olsberg Tenorio PowerSystem Compact (Seite 14 von 44) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

707626

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Installing the stove

The oor on which the stove is installed must be even

and horizontal. The stove may only be installed on an

adequate loadbearing oor. The stove can be stood

on a metal oor sheet or glass sheet to protect the

ooring.

If the ooring or carpet is inammable, a stable and

non-combustible spark protection plate must be used.

This must extend 50 cm to the front and 30 cm to each

side beyond the edge of the combustion chamber

opening. Under the stove no spark protection plate is

required.

Assembly sequence

● The Ø 150 stovepipe connection can be installed at

the top or rear. The stove is supplied ready for con-

nection from above. If you wish to connect it at the

rear, the following steps must be carried out to make

the necessary modications:

- Break out the cover in the back panel.

- Replace the connector sleeve and the sealing

cover.

● Install storage stones.

Comply with the information in the instruction manu-

al included with the storage stones.

● Decide where the stove is to be installed. There

must be no objects made of combustible materials

within a distance of 80 cm of the stove’s radiation

area, measured from the combustion chamber’s in-

spection glass, nor may any be placed within this

area subsequently.

Depending on the installation position of the stove in

front of walls that need to be protected (ammable

or load-bearing), the following distances from walls

need to be observed in accordance with the position

of the combustion chamber door to the wall / side

panel or the back panel (see schematic diagram).

When not dealing with walls that need to be protect-

ed, you merely need to observe a minimum distance

of approx. 5 cm to allow for proper heat dissipation.

● Install the pipe lining (provided on site) in the chim-

ney. The connection height can be individually spec-

ied for a top stovepipe connection, however should

not exceed 1.5 m from the connector sleeve. For the

rear stovepipe connection heights please refer the

“Technical Data“ chapter. No combustible material is

permitted within a radius of 20 cm around the stove

pipe.

● Connect the stovepipe at both connection points

with stove putty so that the stove pipe is permanent-

ly sealed.

● Push the stove onto its planned position and orient it

so that the stovepipe ts into the pipe lining.

The stovepipe connections must be tight. The

stovepipe must not protrude into the chimney.

Bear in mind that on partition walls in accordance

with test specication EN 13240 the temperature

of 85°C can be reached, and with light wallpaper

or similar combustible construction materials this

can result in colour changes.

15 cm

27 cm

80 cm

Stove installed straight in corner

14 cm

80 cm

Stove installed diagonally in corner

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olsberg Tenorio PowerSystem Compact Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info